參數資料
型號： ADUC7032BSTZ-8V-RL
廠商： Analog Devices Inc
文件頁數： 16/128頁
文件大小： 0K
描述： IC BATTERY SENSOR PREC 48-LQFP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 標準包裝
其它名稱： ADUC7032BSTZ-8V-RLDKR
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 112 of 128
SERIAL PERIPHERAL INTERFACE
The ADuC7032 features a complete hardware Serial Peripheral
Interface (SPI) on-chip. SPI is an
industry
standard
synchronous serial interface which allows eight bits of data to
be synchronously transmitted and received simultaneously, i.e.,
full duplex.
The SPI interface is only operational with core clock divider bits
(POWCON[2:0]= 0 or 1).
The SPI Port can be configured for Master or Slave operation
and consists of four pins, which are multiplexed with four
GPIO. The four SPI pins are MISO, MOSI, SCLK and SS . The
pins to which this signals are connected are shown in Table 77.
Table 77 : SPI Output Pins
Pin
Signal
Description
GP0 ( GPIO MODE 1 )
SS
Chip Select
GP1 ( GPIO MODE 1 )
SCLK
Serial Clock
GP2 ( GPIO MODE 1 )
MISO
Master Out, Slave In
GP3 ( GPIO MODE 1 )
MOSI
Master In, Slave Out
These signals are described in detail below.
MISO (Master In, Slave Out Data I/O Pin)
The MISO (master in slave out) pin is configured as an input
line in master mode and an output line in slave mode. The
MISO line on the master (data in) should be connected to the
MISO line in the slave device (data out). The data is transferred
as byte wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin)
The MOSI (master out slave in) pin is configured as an output
line in master mode and an input line in slave mode.
The MOSI line on the master (data out) should be connected to
the MOSI line in the slave device (data in). The data is
transferred as byte wide (8-bit) serial data, MSB first.
SCLK (Serial Clock I/O Pin)
The master serial clock (SCLK) is used to synchronize the data
being transmitted and received through the MOSI SCLK
period. Therefore, a byte is transmitted/received after eight
SCLK periods. The SCLK pin is configured as an output in
master mode and as an input in slave mode.
In master mode polarity and phase of the clock are controlled
by the SPICON register, and the bit-rate is defined in the
SPIDIV register as follow:
)
1
(
2
48
.
20
SPIDIV
MHz
f
k
serialcloc
+
×
=
Equation 3 : SPI Baud Rate Calculation
The maximum speed of the SPI clock is dependant on the clock
divider bits and is summarized in Table 78.
Table 78: SPI speed vs. clock divider bits in master mode
CD bits
0
1
SPIDIV
0x05
0x0B
Max SCLK (MHz)
1.667
0.833
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 5.12 Mb at CD = 0.
The formula to determine the maximum speed is as follow:
4
HCLK
k
serialcloc
f
=
Equation 4 : Maximum Receive Baud Rate
In both master and slave modes, data is transmitted on one edge
of the SCL signal and sampled on the other. Therefore, it is
important that the polarity and phase are configured the same
for the master and slave devices.
Chip Select (SS ) Input Pin
In SPI Slave Mode, a transfer is initiated by the assertion of SS
which is an active low input signal. The SPI port will then
transmit and receive 8-bit data until the transfer is concluded by
de-assertion of SS . In slave mode SS is always an input.
SPI registers definition
The following MMR registers are used to control the SPI
interface:
- SPICON: 16-bit control register
- SPISTA: 8-bit read only status register
- SPIDIV: 8-bit serial clock divider register
- SPITX: 8-bit write only transmit register
- SPIRX: 8-bit read only receive register
相關PDF資料
PDF描述
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
相關代理商/技術參數
參數描述
ADUC7033 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
ADUC7033BCPZ-8L 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays
ADUC7033BCPZ-8L-RL 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel
ADUC7033BSTZ-88 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2
ADUC7033BSTZ-88-RL 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*