參數資料
型號： ADUC7019BCPZ62IRL7
廠商： Analog Devices Inc
文件頁數： 88/104頁
文件大小： 0K
描述： IC MCU 12BIT 1MSPS I2C 40-LFCSP
標準包裝： 750
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PLA，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 14
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 5x12b; D/A 3x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 40-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 84 of 104
FIQ
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface providing the
second-level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Table 165. FIQSTA Register
Name
Address
Default Value
Access
FIQSTA
0xFFFF0100
0x00000000
R
Table 166. FIQSIG Register
Name
Address
Default Value
Access
FIQSIG
0xFFFF0104
0x00XXX0001
R
1
X indicates an undefined value.
Table 167. FIQEN Register
Name
Address
Default Value
Access
FIQEN
0xFFFF0108
0x00000000
R/W
Table 168. FIQCLR Register
Name
Address
Default Value
Access
FIQCLR
0xFFFF010C
0x00000000
W
Bit 31 to Bit 1 of FIQSTA are logically OR’d to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and IRQEN does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN does, as a side effect, clear the same bit in IRQEN.
Also, a bit set to 1 in IRQEN does, as a side effect, clear the
same bit in FIQEN. An interrupt source can be disabled in both
the IRQEN and FIQEN masks.
Note that to clear an already enabled FIQ source, the user must
set the appropriate bit in the FIQCLR register. Clearing an
interrupt’s FIQEN bit does not disable the interrupt.
Programmed Interrupts
Because the programmed interrupts are nonmaskable, they are
controlled by another register, SWICFG, which simultaneously
writes into the IRQSTA and IRQSIG registers and/or the
FIQSTA and FIQSIG registers. The 32-bit SWICFG register is
dedicated to software interrupts(see Table 170). This MMR
allows the control of a programmed source interrupt.
Table 169. SWICFG Register
Name
Address
Default Value
Access
SWICFG
0xFFFF0010
0x00000000
W
Table 170. SWICFG MMR Bit Descriptions
Bit
Description
31:3
Reserved.
2
Programmed interrupt (FIQ). Setting/clearing this bit
corresponds with setting/clearing Bit 1 of FIQSTA
and FIQSIG.
1
Programmed interrupt (IRQ). Setting/clearing this bit
corresponds with setting/clearing Bit 1 of IRQSTA
and IRQSIG.
0
Reserved.
Note that any interrupt signal must be active for at least the
equivalent of the interrupt latency time, which is detected by
the interrupt controller and by the user in the IRQSTA/FIQSTA
register.
TIMERS
The ADuC7019/20/21/22/24/25/26/27/28/29 have four general-
purpose timer/counters.
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
These four timers in their normal mode of operation can be
either free running or periodic.
In free-running mode, the counter decreases from the
maximum value until zero scale and starts again at the
minimum value. (It also increases from the minimum value
until full scale and starts again at the maximum value.)
In periodic mode, the counter decrements/increments from the
value in the load register (TxLD MMR) until zero/full scale and
starts again at the value stored in the load register.
The timer interval is calculated as follows:
If the timer is set to count down then
(
)
Clock
Source
Prescaler
TxLD
Interval
×
=
If the timer is set to count up, then
(
)
Clock
Source
Prescaler
TxLD
Fs
Interval
×
=
The value of a counter can be read at any time by accessing its
value register (TxVAL). Note that when a timer is being clocked
from a clock other than core clock, an incorrect value may be
read (due to an asynchronous clock system). In this configur-
ation, TxVAL should always be read twice. If the two readings
are different, it should be read a third time to get the correct
value.
Timers are started by writing in the control register of the
corresponding timer (TxCON).
相關PDF資料
PDF描述
AT91M42800A-33AU-999 IC MCU 32BIT RISC 144LQFP
ADUC7027BSTZ62-RL IC MCU 12BIT 1MSPS UART 80-LQFP
MB91F267APMC-GE1 IC MCU FLASH 128KB FLASH 64LQFP
ADUC7034BCPZ-RL IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7126BSTZ126IRL IC MCU 16/32B 126KB FLASH 80LQFP
相關代理商/技術參數
參數描述
ADUC702 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7020 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7020BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCP62-U1 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCPZ62 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*