Table 28. VCM Ra" />
參數資料
型號： ADUC7019BCPZ62IRL7
廠商： Analog Devices Inc
文件頁數： 51/104頁
文件大?。?/td> 0K
描述： IC MCU 12BIT 1MSPS I2C 40-LFCSP
標準包裝： 750
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PLA，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 14
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 5x12b; D/A 3x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 40-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 50 of 104
Table 28. VCM Ranges
AVDD
VREF
VCM Min
VCM Max
Signal Peak-to-Peak
3.3 V
2.5 V
1.25 V
2.05 V
2.5 V
2.048 V
1.024 V
2.276 V
2.048 V
1.25 V
0.75 V
2.55 V
1.25 V
3.0 V
2.5 V
1.25 V
1.75 V
2.5 V
2.048 V
1.024 V
1.976 V
2.048 V
1.25 V
0.75 V
2.25 V
1.25 V
CALIBRATION
By default, the factory-set values written to the ADC offset
(ADCOF) and gain coefficient registers (ADCGN) yield
optimum performance in terms of end-point errors and
linearity for standalone operation of the part (see the
Specifications section). If system calibration is required, it is
possible to modify the default offset and gain coefficients to
improve end-point errors, but note that any modification to the
factory-set ADCOF and ADCGN values can degrade ADC
linearity performance.
For system offset error correction, the ADC channel input stage
must be tied to AGND. A continuous software ADC conversion
loop must be implemented by modifying the value in ADCOF until
the ADC result (ADCDAT) reads Code 0 to Code 1. If the
ADCDAT value is greater than 1, ADCOF should be decremented
until ADCDAT reads 0 to 1. Offset error correction is done
digitally and has a resolution of 0.25 LSB and a range of
±3.125% of VREF.
For system gain error correction, the ADC channel input stage
must be tied to VREF. A continuous software ADC conversion
loop must be implemented to modify the value in ADCGN
until the ADC result (ADCDAT) reads Code 4094 to Code 4095.
If the ADCDAT value is less than 4094, ADCGN should be
incremented until ADCDAT reads 4094 to 4095. Similar to the
offset calibration, the gain calibration resolution is 0.25 LSB
with a range of ±3% of VREF.
TEMPERATURE SENSOR
The ADuC7019/20/21/22/24/25/26/27/28/29 provide voltage
output from on-chip band gap references proportional to
absolute temperature. This voltage output can also be routed
through the front-end ADC multiplexer (effectively an additional
ADC channel input) facilitating an internal temperature sensor
channel, measuring die temperature to an accuracy of ±3°C.
The following is an example routine showing how to use the
internal temperature sensor:
int main(void)
{
float a = 0;
short b;
ADCCON = 0x20;
// power-on the ADC
delay(2000);
ADCCP = 0x10;
// Select Temperature
Sensor as an // input to the ADC
REFCON = 0x01; // connect internal 2.5V
reference // to Vref pin
ADCCON = 0xE4; // continuous conversion
while(1)
{
while (!ADCSTA){};
// wait for end of conversion
b = (ADCDAT >> 16);
// To calculate temperature in °C, use
the formula:
a = 0x525 - b;
// ((Temperature = 0x525 - Sensor
Voltage) / 1.3)
a /= 1.3;
b = floor(a);
printf("Temperature: %d
oC\n",b);
}
return 0;
}
BAND GAP REFERENCE
Each ADuC7019/20/21/22/24/25/26/27/28/29 provides an on-
chip band gap reference of 2.5 V, which can be used for the ADC
and DAC. This internal reference also appears on the VREF pin.
When using the internal reference, a 0.47 F capacitor must be
connected from the external VREF pin to AGND to ensure stability
and fast response during ADC conversions. This reference can
also be connected to an external pin (VREF) and used as a refer-
ence for other circuits in the system. An external buffer is required
because of the low drive capability of the VREF output. A program-
mable option also allows an external reference input on the VREF
pin. Note that it is not possible to disable the internal reference.
Therefore, the external reference source must be capable of
overdriving the internal reference source.
Table 29. REFCON Register
Name
Address
Default Value
Access
REFCON
0xFFFF048C
0x00
R/W
The band gap reference interface consists of an 8-bit MMR
REFCON, described in Table 30.
Table 30. REFCON MMR Bit Designations
Bit
Description
7:1
Reserved.
0
Internal reference output enable. Set by user to
connect the internal 2.5 V reference to the VREF pin.
The reference can be used for an external component
but must be buffered. Cleared by user to disconnect
the reference from the VREF pin.
相關PDF資料
PDF描述
AT91M42800A-33AU-999 IC MCU 32BIT RISC 144LQFP
ADUC7027BSTZ62-RL IC MCU 12BIT 1MSPS UART 80-LQFP
MB91F267APMC-GE1 IC MCU FLASH 128KB FLASH 64LQFP
ADUC7034BCPZ-RL IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7126BSTZ126IRL IC MCU 16/32B 126KB FLASH 80LQFP
相關代理商/技術參數
參數描述
ADUC702 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7020 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7020BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCP62-U1 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCPZ62 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*