- 您現在的位置：買賣IC網 > PDF目錄375267 > ADSP-21992 (Analog Devices, Inc.) Mixed Signal DSP Controller With CAN PDF資料下載
參數資料
| 型號： | ADSP-21992 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Mixed Signal DSP Controller With CAN |
| 中文描述： | 混合信號DSP控制器和CAN |
| 文件頁數： | 7/49頁 |
| 文件大小： | 602K |
| 代理商： | ADSP-21992 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Analog
Devices assumes no obligation regarding future manufacturing unless otherwise agreed to in writing.
7
REV. PrA
For current information contact Analog Devices at (781) 937-1799
ADSP-21992
August 2002
PRELIMINARY TECHNICAL DATA
The data bus is configurable to provide an 8 or 16 bit
interface to external memory. Support for word packing lets
the DSP access 16- or 24-bit words from external memory
regardless of the external data bus width.
The memory DMA controller lets the ADSP-21992 move
data and instructions from between memory spaces: inter-
nal-to-external, internal-to-internal, and external-to-
external. On chip peripherals can also use this controller for
DMA transfers.
The embedded ADSP-219x core can respond to up to
seventeen interrupts at any given time: three internal (stack,
emulator kernel, and power down), two external (emulator
and reset), and twelve user defined (peripherals) interrupts.
Programmers assign each of the 32 peripheral interrupt
requests to one of the 12 user defined interrupts. These
assignments determine the priority of each peripheral for
interrupt service.
The following sections provide a functional overview of the
ADSP-21992 peripherals.
Serial Peripheral Interface (SPI) Port
The Serial Peripheral Interface (SPI) Port provides func-
tionality for a generic configurable serial port interface
based on the SPI standard, which enables the DSP to com-
municate with multiple SPI compatible devices. Key
features of the SPI port are:
Interface to host microcontroller or serial EEPROM
Master or slave operation (3 Wire Interface MISO,
MOSI, SCK)
Data rates to 20 Mbaud (16-bit baud rate selector)
8 or 16-bit transfer
Programmable clock phase & polarity
Broadcast Mode - 1 master, multiple slaves
DMA capability & Dedicated interrupts
PF0 can be used as Slave Select Input Line
PF1-PF7 can be used as external Slave Select output
SPI is a 3 wire interface consisting of 2 data pins (MOSI
and MISO), one clock pin (SCK), and a single Slave Select
input (SPISS0) that is multiplexed with the PF0 Flag IO
line and seven Slave Select outputs (SPISEL1 to SPISEL7)
that are multiplexed with the PF1 to PF7 Flag IO lines. The
SPISS0 input is used to select the ADSP-21992 as a slave
to an external master. The SPISEL1 to SPISEL7 outputs
can be used by the ADSP-21992 (acting as a master) to
select/enable up to seven external slaves in an multi device
SPI configuration. In a multimaster or a multi device con-
figuration, all MOSI pins are tied together, all MISO pins
are tied together, and all SCK pins are tied together.
During transfers, the SPI port simultaneously transmits and
receives by serially shifting data in and out on the serial data
line. The serial clock line synchronizes the shifting and
sampling of data on the serial data line.
In master mode, the DSP’s core performs the following
sequence to set up and initiate SPI transfers:
1.
Enables and configures the SPI port operation (data
size, and transfer format).
2.
Selects the target SPI slave with the SPISELx output
pin (reconfigured Programmable Flag pin).
3.
Defines one or more DMA descriptors in Page 0 of I/O
memory space (optional in DMA mode only).
4.
Enables the SPI DMA engine and specifies transfer
direction (optional in DMA mode only).
5.
In non DMA mode only, reads or writes the SPI port
receive or transmit data buffer.
The SCK line generates the programmed clock pulses for
simultaneously shifting data out on MOSI and shifting
data in on MISO. In DMA mode only, transfers continue
until the SPI DMA word count transitions from 1 to 0.
In slave mode, the DSP core performs the following
sequence to set up the SPI port to receive data from a master
transmitter:
1.
Enables and configures the SPI slave port to match the
operation parameters set up on the master (data size
and transfer format) SPI transmitter.
2.
Defines and generates a receive DMA descriptor in
Page 0 of memory space to interrupt at the end of the
data transfer (optional in DMA mode only).
3.
Enables the SPI DMA engine for a receive access
(optional in DMA mode only).
4.
Starts receiving the data on the appropriate SCK edges
after receiving an SPI chip select on the SPISS0 input
pin (reconfigured Programmable Flag pin)
from a master
In DMA mode only, reception continues until the SPI
DMA word count transitions from 1 to 0. The DSP core
could continue, by queuing up the next DMA descriptor.
A slave mode transmit operation is similar, except the DSP
core specifies the data buffer in memory space from which
to transmit data, generates and relinquishes control of the
transmit DMA descriptor, and begins filling the SPI port
data buffer. If the SPI controller is not ready on time to
transmit, it can transmit a “zero” word.
DSP Serial Port (SPORT)
The ADSP-21992 incorporates a complete synchronous
serial port (SPORT) for serial and multiprocessor commu-
nications. The SPORT supports the following features:
Bidirectional: the SPORT has independent transmit and
receive sections.
Double buffered: the SPORT section (both receive and
transmit) has a data register for transferring data words
to and from other parts of the processor and a register for
shifting data in or out. The double buffering provides
additional time to service the SPORT.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21992YST | Mixed Signal DSP Controller With CAN |
| ADSP-21MOD970-510 | Multiport Internet Gateway Processor Data Pump Solution(多端口網關處理器數據泵解決方案) |
| ADSP-21mod970 | Multi-Port Internet Gateway Processor(多口網關處理器) |
| ADSP-21msp58 | DSP Microcomputer(DSP 微計算機) |
| ADSP-21MSP59 | DSP Microcomputer(DSP 微計算機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21992BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:MIXED SIGNAL DSP W/32K DM RAM& 16K PMRAM - Bulk |
| ADSP-21992BST | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-21992BSTZ | 功能描述:IC DSP CONTROLLER 16BIT 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-21992YBC | 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21992YST | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。