參數資料
型號： ADSP-21992
廠商： Analog Devices, Inc.
英文描述： Mixed Signal DSP Controller With CAN
中文描述： 混合信號DSP控制器和CAN
文件頁數： 11/49頁
文件大小： 602K
代理商： ADSP-21992
This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Analog
Devices assumes no obligation regarding future manufacturing unless otherwise agreed to in writing.
11
REV. PrA
For current information contact Analog Devices at (781) 937-1799
ADSP-21992
August 2002
PRELIMINARY TECHNICAL DATA
signal can be programmed to set the FLAG on either a level
(level sensitive input/interrupt) or an edge (edge sensitive
input/interrupt).
The FIO module can also be used to generate an asynchro-
nous unregistered wake up signal FIO_WAKEUP for DSP
core wake up after power down.
The FIO Lines, PF7 - PF1 can also be configured as external
slave select outputs for the SPI Communications Port, while
PF0 can be configured to act as a Slave select input.
The FIO Lines can be configured to act as a PWM shutdown
source for the three phase PWM generation unit of the
ADSP-21992.
Watchdog Timer
The ADSP-21992 integrates a watchdog timer that can be
used as a protection mechanism against unintentional
software events. It can be used to cause a complete DSP and
peripheral reset in such an event. The watchdog timer
consists of a 16-bit timer that is clocked at the external clock
rate (CLKIN or crystal input frequency).
In order to prevent an unwanted timeout or reset, it is
necessary to periodically write to the watchdog timer
register. During abnormal system operation, the watchdog
count will eventually decrement to 0 and a watchdog
timeout will occur. In the system, the watchdog timeout will
cause a full reset of the DSP core and peripherals.
General Purpose Timers
The ADSP-21992 contains a general purpose timer unit
that contains three identical 32-bit timers. The three pro-
grammable interval timers (Timer0, Timer1 and Timer2)
generate periodic interrupts. Each timer can be indepen-
dently set to operate in one of three modes:
Pulse Waveform Generation (PWM_OUT) mode
Pulse Width Count/Capture (WDTH_CAP) mode
External Event Watchdog (EXT_CLK) mode
Each Timer has one bidirectional chip pin, TMR2-TMR0.
For each timer, the associated pin is configured as an output
pin in PWM_OUT Mode and as input pin in WDTH_CAP
and EXT_CLK Modes.
Interrupts
The interrupt controller lets the DSP respond to 17 inter-
rupts with minimum overhead. The DSP core implements
an interrupt priority scheme as shown in
Table 2
. Applica-
tions can use the unassigned slots for software and
peripheral interrupts. The Peripheral Interrupt Controller
is used to assign the various peripheral interrupts to the 12
user assignable interrupts of the DSP core.
There is no assigned priority for the peripheral interrupts
after reset. To assign the peripheral interrupts a different
priority, applications write the new priority to their corre-
sponding control bits (determined by their ID) in the
Interrupt Priority Control register.
Interrupt routines can either be nested with higher priority
interrupts taking precedence or processed sequentially.
Interrupts can be masked or unmasked with the IMASK
register. Individual interrupt requests are logically ANDed
with the bits in IMASK; the highest priority unmasked
interrupt is then selected. The emulation, power down, and
reset interrupts are nonmaskable with the IMASK register,
but software can use the DIS INT instruction to mask the
power down interrupt.
Table 2. Interrupt Priorities/Addresses
Interrupt
Emulator (NMI)
—Highest Priority
Reset (NMI)
Power Down (NMI)
Loop and PC Stack
Emulation Kernel
User Assigned Interrupt
(USR0)
User Assigned Interrupt
(USR1)
User Assigned Interrupt
(USR2)
User Assigned Interrupt
(USR3)
User Assigned Interrupt
(USR4)
User Assigned Interrupt
(USR5)
User Assigned Interrupt
(USR6)
User Assigned Interrupt
(USR7)
User Assigned Interrupt
(USR8)
User Assigned Interrupt
(USR9)
User Assigned Interrupt
(USR10)
User Assigned Interrupt
(USR11)
—Lowest Priority
IMASK/
IRPTL
NA
Vector Address
NA
0
1
2
3
4
0x00 0000
0x00 0020
0x00 0040
0x00 0060
0x00 0080
5
0x00 00A0
6
0x00 00C0
7
0x00 00E0
8
0x00 0100
9
0x00 0120
10
0x00 0140
11
0x00 0160
12
0x00 0180
13
0x00 01A0
14
0x00 01C0
15
0x00 01E0
相關PDF資料
PDF描述
ADSP-21992YST Mixed Signal DSP Controller With CAN
ADSP-21MOD970-510 Multiport Internet Gateway Processor Data Pump Solution(多端口網關處理器數據泵解決方案)
ADSP-21mod970 Multi-Port Internet Gateway Processor(多口網關處理器)
ADSP-21msp58 DSP Microcomputer(DSP 微計算機)
ADSP-21MSP59 DSP Microcomputer(DSP 微計算機)
相關代理商/技術參數
參數描述
ADSP-21992BBC 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:MIXED SIGNAL DSP W/32K DM RAM& 16K PMRAM - Bulk
ADSP-21992BST 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT
ADSP-21992BSTZ 功能描述:IC DSP CONTROLLER 16BIT 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21992YBC 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21992YST 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*