- 您現在的位置：買賣IC網 > PDF目錄16534 > AD9522-1/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9522-1 CLK GEN PDF資料下載
參數資料
| 型號： | AD9522-1/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 68/84頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD9522-1 CLK GEN |
| 設計資源： | AD9522 Eval Board Schematic AD9522 BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9522-1 |
| 主要屬性： | 12 LVDS/24 CMOS 輸出，2.4 GHz VCO |
| 次要屬性： | I²C & SPI 接口 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
AD9522-1
Rev. 0 | Page 70 of 84
Reg.
Addr
(Hex) Bit(s) Name
Description
018
[0]
VCO calibration
now
Bit used to initiate the VCO calibration. This bit must be toggled from 0 to 1 in the active registers. The
sequence to initiate a calibration follows: program to 0, followed by an IO_UPDATE bit (Register 0x232[0]);
then program to 1, followed by another IO_UPDATE bit (Register 0x232[0]). This sequence gives complete
control over when the VCO calibration occurs relative to the programming of other registers that can impact
the calibration (default = 0). Note that the VCO divider (Register 0x1E0[2:0]) must not be static during VCO
calibration.
019
[7:6]
R, A, B counters
SYNC pin reset
[7]
[6]
Action
0
Do nothing on SYNC (default).
0
1
Asynchronous reset.
1
0
Synchronous reset.
1
Do nothing on SYNC.
019
[5:3]
R path delay
R path delay, see Table 2 (default: 0x0).
019
[2:0]
N path delay
N path delay, see Table 2 (default: 0x0).
01A
[7]
Enable STATUS
pin divider
Enables a divide-by-4 on the STATUS pin. This makes it easier to look at low duty-cycle signals out of the
R and N dividers.
[7] = 0; divide-by-4 disabled on STATUS pin (default).
[7] = 1; divide-by-4 enabled on STATUS pin.
01A
[6]
Ref freq monitor
threshold
Sets the reference (REF1/REF2) frequency monitor’s detection threshold frequency. This does not affect the VCO
frequency monitor’s detection threshold (see Table 17, REF1, REF2, and VCO frequency status monitor parameter).
[6] = 0; frequency valid if frequency is above 1.02 MHz (default).
[6] = 1; frequency valid if frequency is above 8 kHz.
01A
[5:0]
LD pin
control
Selects the signal that is connected to the LD pin.
[5]
[4]
[3]
[2]
[1]
[0]
Level or
Dynamic
Signal
Signal at LD Pin
0
LVL
Digital lock detect (high = lock; low = unlock, default).
0
1
DYN
P-channel, open-drain lock detect (analog lock detect).
0
1
0
DYN
N-channel, open-drain lock detect (analog lock detect).
0
1
HIZ
Tristate (high-Z) LD pin.
0
1
0
CUR
Current source lock detect (110 μA when DLD is true).
0
X
LVL
Ground (dc); for all other cases of 0XXXXX not specified.
The selections that follow are the same as for REFMON.
1
0
LVL
Ground (dc).
1
0
1
DYN
REF1 clock (differential reference when in differential mode).
1
0
1
0
DYN
REF2 clock (not available in differential mode).
1
0
1
DYN
Selected reference to PLL (differential reference when in
differential mode).
1
0
1
0
DYN
Unselected reference to PLL (not available in differential mode).
1
0
1
0
1
LVL
Status of selected reference (status of differential reference);
active high.
1
0
1
0
LVL
Status of unselected reference (not available in differential
mode); active high.
1
0
1
LVL
Status of REF1 frequency (active high).
1
0
1
0
LVL
Status of REF2 frequency (active high).
1
0
1
0
1
LVL
(Status of REF1 frequency) AND (status of REF2 frequency).
1
0
1
0
1
0
LVL
(DLD) AND (status of selected reference) AND (status of VCO).
1
0
1
0
1
LVL
Status of VCO frequency (active high).
1
0
1
0
LVL
Selected reference (low = REF1, high = REF2).
1
0
1
0
1
LVL
DLD; active high.
1
0
1
0
LVL
Holdover active (active high).
1
0
1
LVL
Not available, do not use.
1
0
LVL
VS (PLL supply).
1
0
1
DYN
REF1 clock (differential reference when in differential mode).
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J4H-EZ-S | CONVERTER MOD DC/DC 52V 25W |
| ADCLK914/PCBZ | BOARD EVAL FOR ADCLK914 |
| VE-J4F-EZ-S | CONVERTER MOD DC/DC 72V 25W |
| ILC0402ER8N2K | INDUCTOR CER 8.2NH 0402 |
| AD9520-3/PCBZ | BOARD EVAL AD9520-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9522-2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVDS/24 CMOS Output Clock Generator with Integrated 2.2 GHz VCO |
| AD9522-2/PCBZ | 功能描述:BOARD EVAL FOR AD9522-2 CLK GEN RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| AD9522-2BCPZ | 功能描述:IC CLOCK GEN 2.2GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| AD9522-2BCPZ-REEL7 | 功能描述:IC CLOCK GEN 2.2GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| AD9522-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVDS/24 CMOS Output Clock Generator with Integrated 2 GHz VCO |
發布緊急采購，3分鐘左右您將得到回復。