- 您現在的位置：買賣IC網 > PDF目錄371440 > 29PL256N (Spansion Inc.) 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory PDF資料下載
參數資料
| 型號： | 29PL256N |
| 廠商： | Spansion Inc. |
| 英文描述： | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| 中文描述： | 256/128/128字節（16/8/8 M中的x 16位），3.0伏的CMOS只同步讀/寫，頁模式閃存 |
| 文件頁數： | 43/74頁 |
| 文件大?。?/td> | 1968K |
| 代理商： | 29PL256N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
June 6, 2007 S29PL-N_00_A5
S29PL-N MirrorBit
Flash Family
43
D a t a
S h e e t
( P r e l i m i n a r y )
7.8
Software Reset
Software reset is part of the command set (see
Table 12.1 on page 66
) that also returns the device to array
read mode and must be used for the following conditions:
1. To exit Autoselect mode
2. To reset software when DQ5 goes high during write status operation that indicates program or
erase cycle was not successfully completed
3. To exit sector lock/unlock operation.
4. To return to erase-suspend-read mode if the device was previously in Erase Suspend mode.
5. To reset software after any aborted operations
Software Functions and Sample Code
Note
Base = Base Address.
The following is a C source code example of using the reset function. Refer to the
Spansion Low Level Driver
User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash memory software
development guidelines.
/* Example: Reset (software reset of Flash state machine) */
*( (UINT16 *)base_addr + 0x000 ) = 0x00F0;
The following are additional points to consider when using the reset command:
This command resets the banks to the read and address bits are ignored.
Reset commands are ignored once erasure has begun until the operation is complete.
Once programming begins, the device ignores reset commands until the operation is complete
The reset command may be written between the cycles in a program command sequence before
programming begins (prior to the third cycle). This resets the bank to which the system was writing to the
read mode.
If the program command sequence is written to a bank that is in the Erase Suspend mode, writing the reset
command returns that bank to the erase-suspend-read mode.
The reset command may be also written during an Autoselect command sequence.
If a bank has entered the Autoselect mode while in the Erase Suspend mode, writing the reset command
returns that bank to the erase-suspend-read mode.
If DQ1 goes high during a Write Buffer Programming operation, the system must write the
Write to Buffer
Abort Reset
command sequence to RESET the device to reading array data. The standard RESET
command does not work during this condition.
To exit the unlock bypass mode, the system must issue a two-cycle unlock bypass reset command
sequence (see command tables for detail).
Table 7.19
Reset
(LLD Function = lld_ResetCmd)
Cycle
Operation
Word Address
Data
Reset Command
Write
Base + xxxh
00F0h
相關PDF資料 |
PDF描述 |
|---|---|
| 29PS | 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches |
| 29SL800CB-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29SL800CT-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29PN | 制造商:APEM 功能描述: |
| 29PP100-2 | 制造商:SPD 功能描述: |
| 29PP113-1 | 制造商:SOURIAU 功能描述:JEWELRY CLASS |
| 29PP123-1 | 制造商:SPD 功能描述: |
| 29PP123-3 | 制造商:SPD 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。