- 您現在的位置：買賣IC網 > PDF目錄371440 > 29PL256N (Spansion Inc.) 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory PDF資料下載
參數資料
| 型號： | 29PL256N |
| 廠商： | Spansion Inc. |
| 英文描述： | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| 中文描述： | 256/128/128字節（16/8/8 M中的x 16位），3.0伏的CMOS只同步讀/寫，頁模式閃存 |
| 文件頁數： | 30/74頁 |
| 文件大?。?/td> | 1968K |
| 代理商： | 29PL256N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
30
S29PL-N MirrorBit
Flash Family
S29PL-N_00_A5 June 6, 2007
D a t a
S h e e t
( P r e l i m i n a r y )
7.4.3
Sector Erase
The sector erase function erases one or more sectors in the memory array. (See
Table 12.1 on page 66
, and
Figure 7.3 on page 31
.) The device does not require the system to preprogram prior to erase. The Embedded
Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of no less than t
SEA
occurs. During the time-
out period, additional sector addresses and sector erase commands can be written. Loading the sector erase
buffer can be done in any sequence, and the number of sectors can be from one sector to all sectors. The
time between these additional cycles must be less than t
SEA
. Any sector erase address and command
following the exceeded time-out (t
SEA
) may or may not be accepted. Any command other than Sector Erase
or Erase Suspend during the time-out period resets that bank to the read mode. The system can monitor DQ3
to determine if the sector erase timer has timed out (see
DQ3: Sector Erase Timeout State Indicator
on page 40
). The time-out begins from the rising edge of the final WE# pulse in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are
no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data
from the non-erasing banks. The system can determine the status of the erase operation by reading DQ7 or
DQ6/DQ2 in the erasing bank. See
Write Operation Status
on page 37
for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands
are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs,
the sector erase command sequence should be reinitiated once that bank has returned to reading array data,
to ensure data integrity.
Figure 7.3 on page 31
illustrates the algorithm for the erase operation. See
AC Characteristics
on page 59
for
the Erase/Program Operations parameters and timing diagrams.
Software Functions and Sample Code
Note
Unlimited additional sectors can be selected for erase; command(s) must be written within t
SEA
.
The following is a C source code example of using the sector erase function. Refer to the
Spansion Low Level
Driver User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash memory
software development guidelines.
/* Example: Sector Erase Command */
*((UINT16 *)base_addr + 0x555) = 0x00AA; /* write unlock cycle 1 */
*((UINT16 *)base_addr + 0x2AA) = 0x0055; /* write unlock cycle 2 */
*((UINT16 *)base_addr + 0x555) = 0x0080; /* write setup command */
*((UINT16 *)base_addr + 0x555) = 0x00AA; /* write additional unlock cycle 1 */
*((UINT16 *)base_addr + 0x2AA) = 0x0055; /* write additional unlock cycle 2 */
*((UINT16 *)sector_address) = 0x0030; /* write sector erase command */
Table 7.9
Sector Erase
(LLD Function = lld_SectorEraseCmd)
Cycle
Description
Operation
Word Address
Data
1
Unlock
Write
Base + 555h
00AAh
2
Unlock
Write
Base + 2AAh
0055h
3
Setup Command
Write
Base + 555h
0080h
4
Unlock
Write
Base + 555h
00AAh
5
Unlock
Write
Base + 2AAh
0055h
6
Sector Erase Command
Write
Sector Address
0030h
相關PDF資料 |
PDF描述 |
|---|---|
| 29PS | 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches |
| 29SL800CB-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29SL800CT-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29PN | 制造商:APEM 功能描述: |
| 29PP100-2 | 制造商:SPD 功能描述: |
| 29PP113-1 | 制造商:SOURIAU 功能描述:JEWELRY CLASS |
| 29PP123-1 | 制造商:SPD 功能描述: |
| 29PP123-3 | 制造商:SPD 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。