- 您現在的位置：買賣IC網 > PDF目錄373785 > ZL50015 (Zarlink Semiconductor Inc.) Enhanced 1 K Digital Switch with Stratum 4E DPLL PDF資料下載
參數資料
| 型號： | ZL50015 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| 中文描述： | 增強1K的數字交換與地層4E條數字鎖相環 |
| 文件頁數： | 20/122頁 |
| 文件大?。?/td> | 926K |
| 代理商： | ZL50015 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ZL50015
Data Sheet
20
Zarlink Semiconductor Inc.
3.0 Device Overview
The device has sixteen ST-BUS/GCI-Bus inputs (STi0 - 15) and sixteen ST-BUS/GCI-Bus outputs (STio0 - 15).
STio0 - 15 can also be configured as bi-directional pins, in which case STi0 - 15 will be ignored. It is a non-blocking
digital switch with 1024 64 kbps channels and is capable of performing rate conversion between ST-BUS/GCI-Bus
inputs and ST-BUS/GCI-Bus outputs. The ST-BUS/GCI-Bus inputs accept serial input data streams with data rates
of 2.048 Mbps, 4.096 Mbps, 8.192 Mbps and 16.384 Mbps on a per-stream basis. The ST-BUS/GCI-Bus outputs
deliver serial data streams with data rates of 2.048 Mbps, 4.096 Mbps and, 8.192 Mbps and 16.384 Mbps on a
per-stream basis. The device also provides eight high impedance control outputs (STOHZ0 - 7) to support the use
of external ST-BUS/GCI-Bus tristate drivers for the first eight ST-BUS/GCI-Bus outputs (STio0 -7).
By using Zarlink’s message mode capability, microprocessor data stored in the connection memory can be
broadcast to the output streams on a per-channel basis. This feature is useful for transferring control and status
information for external circuits or other ST-BUS/GCI-Bus devices.
The device uses the ST-BUS/GCI-Bus input frame pulse (FPi) and the ST-BUS/GCI-Bus input clock (CKi) to define
the input frame boundary and timing for sampling the ST-BUS/GCI-Bus input streams with various data rates. The
output data streams will be driven by and have their timing defined by FPi and CKi in Divided Slave mode. In
Multiplied Slave mode, the output data streams will be driven by an internally generated clock, which is multiplied
K13, K15,
K14, J11,
J12, J13,
J15, H11,
J14, H12,
H13, H15,
G12, G13
82, 84,
86, 87,
88, 89,
90, 91,
92, 93,
94, 96,
98, 99
A0 - 13
Address 0 to 13 (5 V-Tolerant Inputs)
These pins form the 14-bit address bus to the internal memories
and registers.
M13
41
MOT_INTEL
Motorola_Intel (5 V-Tolerant Input with Enabled Internal
Pull-up)
This pin selects the Motorola or Intel microprocessor interface to
be connected to the device. When this pin is unconnected or
connected to high, Motorola interface is assumed. When this pin is
connected to ground, Intel interface should be used.
P10
43
IRQ
Interrupt (5 V-Tolerant Three-state Output)
This programmable active low output indicates that the internal
operating status of the DPLL has changed. An external pull-up
resistor
MUST
hold this pin at HIGH level.
G2
211
RESET
Device Reset (5 V-Tolerant Input with Internal Pull-up)
This input (active LOW) puts the device in its reset state that
disables the STio0 - 15 drivers and drives the STOHZ0 - 7 outputs
to high. It also preloads registers with default values and clears all
internal counters. To ensure proper reset action, the reset pin must
be low for longer than 1
μ
s. Upon releasing the reset signal to the
device, the first microprocessor access cannot take place for at
least 600
μ
s due to the time required to stabilize the device and
the crystal oscillator from the power-down state. Refer to Section
Section 17.2 on page 46 for details.
PBGA Pin
Number
LQFP Pin
Number
Pin Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ZL50015GAC | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015QCC | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015QCC1 | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50018 | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50018GAC | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL50015_06 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015GAC | 制造商:Microsemi Corporation 功能描述:Switch Fabric 1K x 1K 1.8V/3.3V 256-Pin BGA Tray 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays |
| ZL50015GAG2 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays |
| ZL50015QCC | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256LQFP - Trays |
| ZL50015QCC1 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch with Stratum 4E DPLL |
發布緊急采購，3分鐘左右您將得到回復。