參數資料
型號： XR88C681CJTR-F
廠商： Exar Corporation
文件頁數： 17/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 500
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 帶卷 (TR)
其它名稱： XR88C681CJTR-F-ND
XR88C681
22
Rev. 2.11
Receiver problems such as Parity Error (PE), Receiver
Overrun Error (OE), or Framing Error (FE). The DUART
also does not offer the user to ability to configure one of
the output ports to relay the occurrence of any of these
conditions. Therefore, unless the user is implementing
some sort of “Data Link Layer” error checking scheme
such as CRC, the user is advised to “validate” the
received data by frequently reading the Status Register;
and checking for any non-zero upper-nibble values. This
is especially the case if the user has set the Error Mode to
“Character” (MR1n[5] = 0).
C.6 Servicing DUART Interrupts
Interrupt servicing with the XR88C681 DUART falls into
two broad categories: I-Mode and Z-Mode. I-Mode has
historically been referred to as the “Intel” Mode. Likewise,
the Z-Mode has been referred to as the “Zilog” Mode.
When the DUART is operating in the Z-Mode, the DUART
will place an 8 bit “interrupt vector” on the data bus, to the
CPU, during the “Interrupt Acknowledge” or IACK cycle.
The CPU will read this interrupt vector from the Data Bus,
and determine (from the Interrupt Vector data) the
location of the appropriate interrupt service routine, in
system memory. Additionally, the Z-Mode gives the user
a hardware approach to prioritize the interrupt requests
among numerous peripheral devices. This phenomenon
is discussed in greater detail in
Section C.6.2.
When the DUART is operating in the I-Mode, the DUART
will not provide any interrupt vector information to the
CPU, during the IACK cycle. Interrupt Vector information,
or any means to route program control to the appropriate
Interrupt Service Routine, is accomplished external to the
DUART.
The DUART will be in the I-Mode following power up or a
hardware reset. The user must invoke the “Set Z-Mode”
command, in order to command the DUART into the
Z-Mode.
Although the I-Mode has been referred to as the “Intel”
Mode, and the Z-Mode as the “Zilog” Mode; this does not
mean that the user should only operate the DUART in the
Z-Mode when interfacing a Zilog microprocessor, or in the
I-Mode when interfacing to an Intel microprocessor. The
division between I-Mode and Z-Mode is not necessary
along “corporate” lines. If you are interfacing the DUART
to the following microprocessors/ microcontrollers, then
the DUART must operate in the I-Mode.
D
8051 P
D
8080 CP
D
8085 P
D
68HC11 C
D
Z-80 P (Interrupt Modes 0 and 1)
However, the DUART should be operating in the Z-Mode
when interfacing the following microprocessors/
microcontrollers.
D
8088 P
D
8086 P
D
80286 - 80486 Ps
D
Pentium P
D
Z-80 P (Interrupt Modes 2)
The next few sections will provide detailed discussions of
DUART/Microprocessor
interfacing
and
interrupt
processing
on
each
of
the
above-mentioned
microprocessors.
From this discussion, a detailed
description of I-Mode Interrupt processing and Z-Mode
Interrupt processing will emerge.
C.6.1 I-Mode Interrupt Servicing
The DUART will be in the I-Mode following power up of the
IC, or a hardware reset. In general, a CPU interfacing to a
DUART operating in the I-Mode, will function as follows,
during interrupt servicing.
If the DUART requires interrupt service from the CPU, it
will asserts the -INTR pin to the CPU. Once the CPU has
detected the interrupt request, it will determine the
location of the appropriate interrupt service routine, and
will branch program control to that location. The CPU will
accomplish all of this without providing an “Interrupt
Acknowledge” signal or any further interaction with the
DUART. Once the CPU has eliminated the cause(s) of the
DUART’s interrupt request, the DUART will then negate
its -INTR pin. The CPU will then exit the “DUART”
interrupt service routine and will resume normal
processing.
In general there are two approaches that CPUs
commonly use to locate the appropriate interrupt service
routine, when interfaced with an I-Mode DUART.
D
Direct Interrupt Processing
D
(External) Vectored-Interrupt Processing
Direct Interrupt Processing
If a CPU employs “Direct Interrupt Processing” then once
the CPU has detected the interrupt request, and has
completed its current instruction, the CPU will branch
相關PDF資料
PDF描述
ST16C2550IQ48TR-F IC UART FIFO 16B DUAL 48TQFP
XR16C2550IMTR-F IC UART FIFO 16B DUAL 48TQFP
ST78C34CP40-F IC UART FIFO 83B 40PDIP
XR16M2551IL32TR-F IC UART FIFO 16B DUAL 32QFN
XR16L2551ILTR-F IC UART FIFO 16B DUAL 32QFN
相關代理商/技術參數
參數描述
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40-F 功能描述:UART 接口集成電路 0.5V-2V UART temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*