參數資料
型號： XIB-E
廠商： Digi International/Maxstream
文件頁數： 54/64頁
文件大小： 1858K
描述： BOARD INTERFACE ETHERNET
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
54?/DIV>
Automatic DIP Switch Configurations
Each time the module assembly (XStream Module mounted to an XIB-R Interface Board) is
powered on, intelligence on t
Board sends AT Commands that program
the module based on positions
uring
er-on sequence affect
To avoid overwriting previous
 (due to the automatic
configurations that take place
dule assembly is powered on), it is necessary to
disable a processor located on
rface board. To disable the processor, populate J7 of
the XIB-R Interface Board. By
 
Table燘02. Module燩owerup燨ption
he MaxStream Interface
 of the DIP Switch. Automatic configurations that take place d
 module parameter values as shown below.
ly stored custom configurations
the pow
 each time the mo
 the XIB-R inte
 default, J7 jumper is not populated.
s?J7爅umper燼nd燙onfig燬witch)牋?/DIV>
Condition
Behavior
If J7 is popu
Processor is disable
lated
d and AT Commands are not sent to the Module.
If Config Switch is pressed
Processor is disabled and Module enters into AT Command Mode.
If J7 is NOT populated and Config Switch
is NOT pressed
Execute logic as shown in table below.
 
 
Table燘03. AT燙ommands燬ent燼s爎esult爋f燚IP燬witch燬ettings?SW?燚IP燬witch)牋?/DIV>
Condition
Behavior
Restore Default Parameter Values of the Module
If SW1 & SW2 are ON (up)
AT Commands sent:    ATRE (Restore Defaults) Command
   
 
ATWR (Write) Command
Serial Interfacing Options
If SW1 is ON (up)
AT Commands sent:    ATCS 0 (RS-232 Operation: CTS function for CTS line,
   
 
DB-9 pin 8)
   
 
ATCD 2 (DO3 - RX LED = low)
If SW1 is OFF (down)
AT Commands sent:    ATCS 3 (RS-485 or RS-422 Operation)
   
 
ATCD 2 (DO3 - RX LED = low)
Parity Options
If SW5 & SW6 are OFF (down)
AT Commands sent:    ATNB 0 (parity = none)
If SW5 is OFF (down) & SW6 is ON (up)     AT Commands sent:    ATNB 1 (parity = even)
If SW5 is ON (up) & SW6 is OFF (down)     AT Commands sent:    ATNB 2 (parity = odd)
If SW5 is ON (up) & SW6 is ON (up)
AT Commands sent:    ATNB 5 (parity = 9th bit data over-the-air)
Exit AT Command Mode
Always
AT Commands sent:    ATCN (Exit AT Command Mode)
 
相關PDF資料
PDF描述
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
相關代理商/技術參數
參數描述
XIB-R 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*