參數資料
型號： XIB-E
廠商： Digi International/Maxstream
文件頁數： 46/64頁
文件大小： 1858K
描述： BOARD INTERFACE ETHERNET
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
46?/DIV>
Sleep Modes and Connections
Cyclic sleep can be used with the remote modules to conserve power. ST Time before Sleep
ssage is detected, the module will stay awake
n
 that
 
ng enough to account for the time it could take
Parameter defines how long after a disconnect a remote will stay awake. A module is not allowed
to enter sleep mode when it is engaged in a connection. A module will wake as defined by SM
parameter and check for an RF message. If a me
only if the message is a connect message from the base for this module. DI3 (pin 2) wake-up ca
be used to wake a remote module. Usually the connection on DI3 should also be enabled so
a connection is established on wake-up.
NOTE: The ST (Time Before Sleep) time must be set lo
to make a connection if several remote modules get a connection before a remotes ST times out.
 
into pin sleep
al not defined by the cyclic sleep modes.
I/
Pin sleep can also be used with a remote module. A module will not be allowed
while a connection is active. Usually the connection on DI3 (DR = 4) should also be enabled so
that a connection is established on wakeup. Pin wake-up could also be used to scan for a
connection at an interv
O Passing and Connections
I/O lines can be passed between a remote and base module by enabling I/O line passing (se
RT, DR, CD, CO, CS, BK, BO
e the
 commands). When a connection is not active, the output lines on the
les will be in their default state. When a connection is established, the
Moni
base and remote modu
base and remote output line will be set to reflect the corresponding input lines.
toring Connections
The DO3 pin (RX LED) can be used to show when a connection is active on both remote and bas
modules. This is the default condition. This line will be asserted (high) during a connectio
de-asserted (low) when there is no connection.
e
n and
o send the CONNECT XXXX string (where XXXX is the
s MY (Source Address) p
 anytime a connection is established. Refer
ssage
A base module can also be set t
connecting module
n Me
arameter)
to CM (Connectio
) Command.
相關PDF資料
PDF描述
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
相關代理商/技術參數
參數描述
XIB-R 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*