參數資料
型號： XIB-E
廠商： Digi International/Maxstream
文件頁數： 29/64頁
文件大?。?/td> 1858K
描述： BOARD INTERFACE ETHERNET
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
PW (Pin Wake-up) Command
AT Command: ATPW
Binary Command: 0x1D (29 decimal)
Parameter Range:   0  1
 
Parameter
Configuration
 
0
Disabled
 
1
Enabled
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: SM (Sleep Mode), ST (Time
before Sleep)
Minimum Firmware Version Required: 4.22
<Sleep (Low Power)> Under normal operation, a
module in Cyclic Sleep Mode cycles from an
active state to a low-power state at regular
intervals until data is ready to be received. If the
PW Parameter is set to 1, SLEEP (pin 2) can be
used to wake the module from Cyclic Sleep. If the
SLEEP pin is de-asserted (low), the module will
be fully operational and will not go into Cyclic
Sleep. Once SLEEP is asserted, the module will
remain active for the period of time specified by
ST (Time before Sleep) Command and will return
to Cyclic Sleep Mode (if no data is ready to be
transmitted). PW Command is only valid if Cyclic
Sleep has been enabled.
RB (Packetization Threshold) Command
AT Command: ATRB
Binary Command: 0x20 (32 decimal)
<Serial Interfacing> RF transmission will
commence when data is in the DI Buffer and
either of the following criteria are met:
Parameter Range: 0  0x100 [bytes]
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
29?/DIV>
"   RO times out on the UART receive lines
(ignored if RO = 0)
"   RB characters have been received by the
UART (ignored if RB = 0)
If PK is lowered below the value of RB; RB is
automatically lowered to match PK.
Note: RB and RO criteria only apply to the first
packet of a multi-packet transmission. If data remains in the DI Buffer after the first packet,
transmissions will continue in streaming manner until there is no data left in the DI Buffer (UART
receive buffer).
(Maximum value equals the current value of PK
Parameter (up to 0x100 HEX (800 decimal))
Default Parameter Value: 1
Number of bytes returned: 2
Related Commands: PK (RF Packet Size), RO
(Packetization Timeout)
Minimum Firmware Version Required: 4.30
RE (Restore Defaults) Command
<Diagnostics> RE Command restores all
configurable parameters to factory default
settings. However, RE Command will not write
the restored values to non-volatile (persistent) memory. Issue the WR (Write) Command after
the RE command to save restored parameter values to non-volatile memory.
AT Command: ATRE
Binary Command: 0x0E (14 decimal)
RN (Delay Slots) Command
<Networking & Security> RN Command is only
applicable if retries have been enabled [RR
(Retries) parameter > 0], or if forced delays will
be inserted into a transmission [TT (Streaming
Limit) parameter > 0]. RN Command is used to
adjust the time delay that the transmitter inserts
before attempting to resend a packet. If the
transmitter fails to receive an acknowledgement
after sending a packet, it will insert a random
number of delay slots (ranging from 0 to (RN
minus 1)) before attempting to resend the packet. Each delay slot lasts for a period of 38ms.
AT Command: ATRN
Binary Command: 0x19 (25 decimal)
Parameter Range:   0  0xFF [slots]
Default Parameter Value: 0
(no delay slots are inserted)
Number of bytes returned: 1
Related Commands: RR (Retries), TT
(Streaming Limit)
Minimum Firmware Version Required: 4.22
If two modules attempted to transmit at the same time, the random time delay after packet
failure would allow one of the two modules to transmit the packet successfully, while the other
would wait until the channel opens up to begin transmission.
相關PDF資料
PDF描述
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
相關代理商/技術參數
參數描述
XIB-R 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*