參數資料
型號： XIB-E
廠商： Digi International/Maxstream
文件頁數： 28/64頁
文件大?。?/td> 1858K
描述： BOARD INTERFACE ETHERNET
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
MY (Source Address) Command
AT Command: ATMY
Binary Command: 0x2A (42 decimal)
Parameter Range:   0  0xFFFF
Default Parameter Value: 0xFFFF (Disabled 
the DT (Destination Address) parameter serves
as both source and destination address.)
Number of bytes returned: 2
Related Commands: DT (Destination Address),
HP (Hopping Channel), ID (Modem VID), MK
(Address Mask), AM (Auto-set MY)
Minimum Firmware Version Required: 4.30
<Networking & Security> Set/Read the source
address of the module.
Refer to the Addressing section [p36] of the RF
Communication Modes chapter for more
information.
 
 
 
 
NB (Parity) Command
AT Command: ATNB
Binary Command: 0x23 (35 decimal)
Parameter Range:   0  5
 
Parameter
Configuration
 
0
8-bit (no parity or
7-bit (any parity)
 
1
8-bit even
 
2
8-bit odd
 
3
8-bit mark
 
4
8-bit space
 
5
9-bit
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.30
(previous versions did not support the 9
th
 bit.
<Serial Interfacing> Select/Read parity settings
for UART communications.
 
 
 
 
 
 
 
 
 
 
 
PC (Power-up Mode) Command
AT Command: ATPC
Binary Command: 0x1E (30 decimal)
Parameter Range:   0  1
 
Parameter
Configuration
 
0
Power-up to Idle Mode
 
1
Power-up to
AT Command Mode
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.22
<Command Mode Options> PC Command allows
the module to power-up directly into AT
Command Mode from reset or power-on. If PC
Command is enabled with SM Parameter set to 1,
DI3 (pin 2) can be used to enter the module into
AT Command Mode. When the DI3 pin is de-
asserted (low), the module will wake-up in AT
Command Mode. This behavior allows module
DTR emulation.
 
 
 
PK (RF Packet Size) Command
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
28?/DIV>
<Serial Interfacing> Set/Read the maximum size
of the RF packets sent out a transmitting
module. The maximum packet size can be used
along with the RB and RO parameters to
implicitly set the channel dwell time.
Changes to this parameter may have a
secondary effect on the RB (Packet Control
Characters) parameter. RB must always be less
than or equal to PK. If PK is changed to a value
less than the current value of RB, RB is automatically lowered to be equal to PK.
AT Command: ATPK
Binary Command: 0x29 (41 decimal)
Parameter Range:   0  0x100 [Bytes]
Default Parameter Value: 0x40 (64 decimal)
Number of bytes returned: 2
Related Commands: RB (Packetization
Threshold), RO (Packetization Timeout)
Minimum Firmware Version Required: 4.30
相關PDF資料
PDF描述
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
相關代理商/技術參數
參數描述
XIB-R 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*