參數資料
型號： W9751G6JB-25A
廠商： WINBOND ELECTRONICS CORP
元件分類： DRAM
英文描述： 32M X 16 DDR DRAM, 0.4 ns, PBGA84
封裝： 12.50 X 8 MM, ROHS COMPLIANT, WBGA-84
文件頁數： 14/86頁
文件大?。?/td> 1030K
代理商： W9751G6JB-25A
W9751G6JB
Publication Release Date: Mar. 10, 2010
- 21 -
Revision A02
7.3.3
Write Command
( CS = "L", RAS = "H", CAS = "L", WE = "L", BA0, BA1 = Bank, A10 = "L", A0 to A9 = Column
Address)
The WRITE command is used to initiate a burst write access to an active row. The value on BA0, BA1
inputs selects the bank, and the A0 to A9 address inputs determine the starting column address. The
address input A10 determines whether or not Auto-precharge is used. If Auto-precharge is selected,
the row being accessed will be precharged at the end of the WRITE burst; if Auto-precharge is not
selected, the row will remain open for subsequent accesses.
7.3.4
Burst Read with Auto-precharge Command
( CS = "L", RAS = "H", CAS ="L", WE = "H", BA0, BA1 = Bank, A10 = "H", A0 to A9 = Column
Address)
If A10 is HIGH when a Read Command is issued, the Read with Auto-precharge function is engaged.
The DDR2 SDRAM starts an Auto-precharge operation on the rising edge which is (AL + BL/2) cycles
later than the read with AP command if tRAS(min) and tRTP(min) are satisfied.
7.3.5
Burst Write with Auto-precharge Command
( CS = "L", RAS = "H", CAS = "L", WE = "L", BA0, BA1 = Bank, A10 = "H", A0 to A9 = Column
Address)
If A10 is HIGH when a Write Command is issued, the Write with Auto-precharge function is engaged.
The DDR2 SDRAM automatically begins precharge operation after the completion of the burst write
plus write recovery time (WR) programmed in the mode register.
7.3.6
Precharge All Command
( CS = "L", RAS = "L", CAS = "H", WE = "L", BA0, BA1 = Don’t Care, A10 = "H", A0 to A9 and
A11 to A12 = Don’t Care)
The Precharge All command precharge all banks simultaneously. Then all banks are switched to the
idle state.
7.3.7
Self Refresh Entry Command
( CS = "L", RAS = "L", CAS = "L", WE = "H", CKE = "L", BA0, BA1, A0 to A12 = Don’t Care)
The Self Refresh command can be used to retain data, even if the rest of the system is powered
down. When in the Self Refresh mode, the DDR2 SDRAM retains data without external clocking. The
DDR2 SDRAM device has a built-in timer to accommodate Self Refresh operation. ODT must be
turned off before issuing Self Refresh command, by either driving ODT pin LOW or using an EMRS
command. Once the command is registered, CKE must be held LOW to keep the device in Self
Refresh mode. The DLL is automatically disabled upon entering Self Refresh and is automatically
enabled upon exiting Self Refresh. When the DDR2 SDRAM has entered Self Refresh mode, all of the
external signals except CKE, are ”Don’t Care”.
The clock is internally disabled during self refresh operation to save power. The user may change the
external clock frequency or halt the external clock one clock after Self Refresh entry is registered;
however, the clock must be restarted and stable before the device can exit self refresh operation.
相關PDF資料
PDF描述
W9751G8JB-18 DDR DRAM, PBGA84
W9812G21H-6I 4M X 32 SYNCHRONOUS DRAM, 5 ns, PDSO86
W9812G21H-6C 4M X 32 SYNCHRONOUS DRAM, 4.5 ns, PDSO86
W9812G6JH-6 8M X 16 SYNCHRONOUS DRAM, 5 ns, PDSO54
W986416AH-10 4M X 16 SYNCHRONOUS DRAM, 8 ns, PDSO54
相關代理商/技術參數
參數描述
W9751G6JB-3 制造商:Winbond Electronics Corp 功能描述:512MB DDRII
W9751G6KB 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M ? 4 BANKS ? 16 BIT DDR2 SDRAM
W9751G6KB-18 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W9751G6KB-25 功能描述:IC DDR2 SDRAM 512MBIT 84WBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6
W9751G6KB25A 制造商:WINBOND 制造商全稱:Winbond 功能描述:Double Data Rate architecture: two data transfers per clock cycle
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*