參數資料
型號: TSC2302IRGZRG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC48
封裝: GREEN, PLASTIC, VQFN-48
文件頁數: 76/85頁
文件大小: 1483K
代理商: TSC2302IRGZRG4
www.ti.com
TSC2302
SLAS394 – JULY 2003
With this in mind, power to the TSC2302 must be clean and well bypassed. A 0.1-F ceramic bypass capacitor
should be placed as close to the device as possible on each supply pin to its respective ground pin. A 1-F to
10-F capacitor may also be needed if the impedance of the connection between a supply and the power supply
is high.
A bypass capacitor on the SAR VREF pin may not be absolutely necessary because this reference is buffered by
an internal op amp, but a 0.1uF bypass capacitor may reduce noise on this reference. If an external reference
voltage originates from an op amp, make sure that it can drive any bypass capacitor that is used without
oscillation.
The TSC2302 SAR converter architecture offers no inherent rejection of noise or voltage variation in regards to
using an external reference input. This is of particular concern when the reference input is tied to the power
supply. Any noise and ripple from the supply appears directly in the digital results. While high frequency noise
can be filtered out, voltage variation due to line frequency (50 Hz or 60 Hz) can be difficult to remove.
The HPGND pin must be connected to a clean ground point. In many cases, this is the analog ground for the
SAR converter. Avoid connections which are too near the grounding point of a microcontroller or digital signal
processor. If needed, run a ground trace directly from the converter to the power supply entry or battery
connection point. The ideal layout includes an analog ground plane dedicated to the converter and associated
analog circuitry.
In the specific case of use with a resistive touch screen, care must be taken with the connection between the
converter and the touch screen. Since resistive touch screens have fairly low resistance, the interconnection
should be as short and robust as possible. Loose connections can be a source of error when the contact
resistance changes with flexing or vibrations.
As indicated previously, noise can be a major source of error in touch screen applications (e.g., applications that
require a back-lit LCD panel). This EMI noise can be coupled through the LCD panel to the touch screen and
cause flickering of the converted data. Several things can be done to reduce this error, such as utilizing a touch
screen with a bottom-side metal layer connected to ground. This couples the majority of noise to ground.
Additionally, filtering capacitors, from Y+, Y-, X+, and X- to ground, can also help. Note, however, that the use of
these capacitors increases screen settling time and requires longer panel voltage stabilization times, as well as
increased precharge and sense times for the touch screen control circuitry of the TSC2302.
78
相關PDF資料
PDF描述
TSDC4872IJT 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8
TS4872IJT 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8
TSH103ID 3 CHANNEL, VIDEO AMPLIFIER, PDSO8
TSH103IDT 3 CHANNEL, VIDEO AMPLIFIER, PDSO8
TSH120ICT SPECIALTY CONSUMER CIRCUIT, PDSO6
相關代理商/技術參數
參數描述
TSC2303IZQZ 制造商:Texas Instruments 功能描述:
TSC2303IZQZR 制造商:Texas Instruments 功能描述:
TSC236 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor
TSC236CIC0 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor
TSC236CZ C0 功能描述:兩極晶體管 - BJT High voltage NPN Transistor RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2