參數資料
型號: TPS65800RTQTG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
封裝: 8 X 8 MM, GREEN, PLASTIC, QFN-56
文件頁數: 46/98頁
文件大?。?/td> 2077K
代理商: TPS65800RTQTG4
www.ti.com
2 .75 A
500 mA
200 mA
750 mA
800 mA
300 mA
- 250 mA
SYSTEMLOAD
INPUT
CURRENT
BATTERY
CHARGE
CURRENT
BATTERY
CHARGING,
USBINPUT LIMIT
SET TO 2.75 A
BATTERY
CHARGING,
INPUT LIMIT SET
TO 500 mA
BATTERY
DISCHARGING,
SUPPLEMENT
MODESET
(800mA DEFINED
BY RSET VALUE)
I(USB)
I(OUT )
CHARGE TERMINATION AND RECHARGE
I
TERM +
V
TERM
K
SET
R
SET
(4)
SLVS606C – SEPTEMBER 2005 – REVISED FEBRUARY 2007
The ISET1 resistor always sets the maximum charge current, if the AC input is selected. When the USB input is
selected, the maximum charge current is defined by the USB input current limit and the programmed charge
current. If the USB input current limit is lower than the IO(OUT) value, the battery switch is set in the dropout
region and the charge current is defined by the input current limit value and system load, as shown in the
following curves:
Figure 36. Input Current Limit Impact on Effective Charge Current
The TPS65800 monitors the charging current during the voltage regulation phase. Charge is terminated when
the charge current is lower than an internal threshold, set to 10% (typ) of the fast charge current rate. The
termination point applies to both AC and USB charging, and it can be calculated as follows:
where
VTERM is the termination detection voltage reference.
The voltage at ISET1 pin is monitored to detect termination, and termination is detected when V(SET1) < VTERM
(0.25 V typ). The voltage reference VTERM is internally set to 10% of the VSET reference voltage, and it is
modified if the reference voltage VSET is scaled via I
2C register CHG_CONFIG bits ISET1_1 and ISET1_0.
VTERM is reduced by the same percentage used to scale down VSET .
The table below shows charge current and termination thresholds for a 1-A charge current set (1-k
resistor
connected to ISET1 pin), with the selected input current limit set to a value higher than the programmed charge
current. The termination current is scaled for all charge current modes (AC or USB), as it is always set by the
ISET1 pin external resistor value.
Table 7. Charge Current and Termination Threshold Selection Example
Charge Control Register Bits
Charge Current, (% of typical value
Vset
Vterm
Charge
Termination
programmed by ISET1 resistor)
(V)
(mV)
Current (A)
Current (mA)
ISET1_1
ISET1_0
0
25%
0.6
60
0.24
20
0
1
50%
1.25
115
0.5
40
1
0
75%
1.9
160
0.78
60
1
100%
2.5
250
1
100
50
相關PDF資料
PDF描述
TPS65800RTQT 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
TPS65800RTQRG4 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
TPS658600AZQZT POWER SUPPLY MANAGEMENT CKT, PBGA120
TPS658610AZQZR POWER SUPPLY MANAGEMENT CKT, PBGA120
TPS658610AZQZT POWER SUPPLY MANAGEMENT CKT, PBGA120
相關代理商/技術參數
參數描述
TPS65810EVM 功能描述:電源管理IC開發工具 TPS65810 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS65810RTQR 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65810RTQRG4 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65810RTQT 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65810RTQTG4 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel