- 您現在的位置：買賣IC網 > PDF目錄69522 > TPS65800RTQTG4 (TEXAS INSTRUMENTS INC) 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65800RTQTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 42/98頁 |
| 文件大?。?/td> | 2077K |
| 代理商： | TPS65800RTQTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
www.ti.com
Boot-Up Algorithm
No Battery Detection Circuit
BAT
OUT
V
-V
(OUT)
(NOBATID)
+
_
ANLG1
Battery
I C
2
TPS65800
PACKID
Resistor
Using the Input Power to Run the System and Charge the Battery Pack
BATTERY CHARGE MANAGEMENT FUNCTION
Operating Modes
SLVS606C – SEPTEMBER 2005 – REVISED FEBRUARY 2007
During the initial TPS65800 power-up the contents of the ISET2, CE and SUSPEND bits on the control register
are ignored for a time period tBOOT. During that time the charger is enabled, and the selected input current limit is
set internally to 100 mA max. At the end of tBOOT period the control register settings are implemented.
The ANLG1 pin may be used to detect the connection of an external resistor that is embedded in a battery pack
and is used as a pack ID function. The ANLG1 pin has an internal current source connected between OUT and
ANLG1, which is enabled automatically when the TPS65800 is not in SLEEP mode. The current levels for
ANLG1 pin can be programmed via I2C register ADC_WAIT, bits BATID_n, as shown below:
Figure 33. Battery Removal Detection, ANLG1 Pin
An internal comparator with a fixed deglitch time, t DGL(NOBAT) monitors the ANLG1 pin voltage, if V(ANLG1) >
V(OUT) - VNOBATID a battery removed condition is detected and an internal discharge switch is activated,
connecting an internal resistor from BAT pin to AGND1. Note that ANLG1 can also be used as an analog input
for the ADC converter, in this case the voltage at pin ANLG1 must never exceed the V(OUT) - VNOBATID
threshold to avoid undesired battery discharge.
The external supply connected to AC or USB pins must be capable of supplying the system power and the
charger current. If the external supply power is not sufficient to run the system and charge the battery pack the
TPS65800 executes a two-stage algorithm that prevents a low voltage condition at the system power bus:
1. The charge current is reduced, until the total (charger + system current) is at a level that can be supplied
by the external input supply. This function is implemented by a dedicated charger control loop (see DPPM
section in charger functional description for additional details).
2. The battery switch is turned ON if the charge current is reduced to zero and the input current is not
enough to run the system. In this mode of operation both the battery and the external input power supply
the system power ( supplement operation mode).
The supplement operation mode is automatically set by the TPS65800 when the input power is switched to the
OUT pin, and the OUT pin voltage falls below the battery voltage.
The TPS65800 supports charging of single-cell Li-Ion or Li-Pol battery packs. The charge process is executed in
three phases: precharge (or preconditioning), constant current and constant voltage.
47
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65800RTQT | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65800RTQRG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS658600AZQZT | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
| TPS658610AZQZR | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
| TPS658610AZQZT | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810EVM | 功能描述:電源管理IC開發工具 TPS65810 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS65810RTQR | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQRG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQT | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。