- 您現在的位置：買賣IC網 > PDF目錄69522 > TPS65800RTQTG4 (TEXAS INSTRUMENTS INC) 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65800RTQTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 32/98頁 |
| 文件大?。?/td> | 2077K |
| 代理商： | TPS65800RTQTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
www.ti.com
SLVS606C – SEPTEMBER 2005 – REVISED FEBRUARY 2007
When the RESPWRON signal is LO, all internal and external interrupts are ignored. As a result, the open-drain
output that asserts the INT pin LO during a NORMAL MODE interrupt request is disabled. The INT pin is then
asserted HI via a pullup resistor that is typically connected to VOUT. After the RESPWRON signal goes HI, the
interrupt controller is given control of the INT pin. Finally, the rising edge of the RESPWRON pin should be used
to indicate the PMIC has transitioned from the RESET STATE to the POWER GOOD CHECK STATE. At that
point, the interrupt controller asserts an interrupt if necessary.
POWER GOOD CHECK – In the power good check mode the power good comparators are enabled, providing
status on the integrated supplies output voltages. An output voltage is considered as out of regulation and
generates a fault condition if the output voltage is below 90% of the target output voltage regulation value. If a
power good fault is detected the SLEEP mode is set, if a power good fault is not detected the NORMAL mode is
set.
The individual supply power good status can be masked via an I2C register PGOODFAULT_MASK. Supplies
that have their power-good fault status masked do not generate a power good fault. However, the status bit for
the supply indicates that the output voltage is out of regulation.
The power good mask register bits default to masked upon power up.
NORMAL MODE – If a power good fault is not present at the end of the power good check mode the NORMAL
mode starts. In this mode of operation the I2C registers define the TPS65800 operation, and the host has full
control on operation modes, parameter settings, etc. The normal state operation ends if a thermal fault, system
low voltage fault ( V(SYS_IN) < VLOW_SYS ) or power-good fault is detected. A thermal fault or system low voltage
fault sets the SLEEP mode operation, a power good fault sets the NO POWER operation mode. From the
normal mode the converters SM1 and SM2 can be set in the STANDBY mode, with reduced output voltages. In
NORMAL mode either an I2C register bit (SOFT_RESET register bit SOFT_RST) or a hardware input (
HOT_RESET pin set to LO) can trigger a transition to the RESET state, enabling implementation of a host reset
function. In NORMAL mode an I2C register bit (SOFT_RESET register bit SLEEP_MODE) can trigger a
transition to SLEEP mode.
SLEEP MODE – The SLEEP mode is set when a thermal fault or system low voltage fault is detected, under
NORMAL operation mode set. This operation mode is also set when a power good fault is detected during the
power good check state or via the I2C bit SLEEP_MODE. In the SLEEP mode the RESPWRON output is set to
LO, and the I2C registers keep the same contents as in the state preceding SLEEP mode, with the exception of
the following control bits, which are reset to the default power-up values:
1. LDO1, -2, -3, -4, -5, and RTC_OUT are enabled, SIM LDO is disabled: EN_LDO register set to default
values
2. LDO0 disabled, all GPIO’s with no control function assigned: GPIO12, GPIO3 registers set to default
values
3. White LED driver is set to OFF: SM3_SET register has all bits set to LO
4. RGB drivers are set to OFF: RGB_FLASH, RGB_RED, RGB_GREEN, RGB_BLUE registers are set to
default values
5. PWM, PWM_LED drivers OFF: PWM, LED_PWM registers are set to default values
6. ADC engine reset to power up default: ADC_SET, ADC_DELAY, ADC_WAIT registers are set to default
values
In SLEEP mode, the power path and main internal blocks are still active, but the internal integrated
supply sequencing is disabled. As a result of that, during SLEEP mode ALL integrated supplies (ALL
LDOs, ALL buck converters) are disabled.
At the end of the SLEEP mode, the sequencer block uses the I2C control register values (which were reset to
the default power-up values) to sequence the integrated power supplies. The SLEEP mode ends when one of
the three following events happens:
1. If SLEEP was set by thermal fault: The SLEEP mode ends only when all external input supplies and
battery pack are removed and a UVLO condition is detected by the TPS65800, setting the NO POWER
mode.
2. If SLEEP was set by a system low voltage detection, or I2C bit SLEEP_MODE, only with battery present:
Input power must be connected, setting the TPS65800 in the ENABLE mode. If no input power is
inserted, the battery discharges until the TPS65800 detects an UVLO condition and enters the NO
POWER mode.
38
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65800RTQT | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65800RTQRG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS658600AZQZT | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
| TPS658610AZQZR | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
| TPS658610AZQZT | POWER SUPPLY MANAGEMENT CKT, PBGA120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810EVM | 功能描述:電源管理IC開發工具 TPS65810 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS65810RTQR | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQRG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQT | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。