參數資料
型號： SP37E760-MD
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 外設及接口
英文描述： 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
中文描述： MULTIFUNCTION PERIPHERAL, PQFP100
封裝： TQFP-100
文件頁數： 36/78頁
文件大?。?/td> 510K
代理商： SP37E760-MD
The Status Port is located at an offset of ‘01H’ from the base address. Bits 0 - 2 are not implemented as register bits,
during a read of the Printer Status Register these bits are a low level. The bits of the Status Port are defined as
follows:
SMSC DS – SP37E760
Page 36
Rev. 04/13/2001
5.4.4.2.1
The level on the nFault input is read by the CPU as bit 3 of the Device Status Register.
BIT 3 nFault
5.4.4.2.2
The level on the Select input is read by the CPU as bit 4 of the Device Status Register.
BIT 4 Select
5.4.4.2.3
The level on the PError input is read by the CPU as bit 5 of the Device Status Register. Printer Status Register.
BIT 5 PError
5.4.4.2.4
The level on the nAck input is read by the CPU as bit 6 of the Device Status Register.
BIT 6 nAck
5.4.4.2.5
The complement of the level on the BUSY input is read by the CPU as bit 7 of the Device Status Register.
5.4.4.3
DEVICE CONTROL REGISTER (dcr)
ADDRESS OFFSET = 02H
The Control Register is located at an offset of ‘02H’ from the base address. The Control Register is initialized to zero
by the RESET input, bits 0 to 5 only being affected; bits 6 and 7 are hard wired low.
BIT 7 nBusy
5.4.4.3.1
This bit is inverted and output onto the nSTROBE output.
BIT 0 STROBE - STROBE
5.4.4.3.2
This bit is inverted and output onto the nAUTOFD output. A logic 1 causes the printer to generate a line feed after
each line is printed. A logic 0 means no autofeed.
BIT 1 AUTOFD - AUTOFEED
5.4.4.3.3
This bit is output onto the nINIT output without inversion.
BIT 2 nINIT - nINITIATE OUTPUT
5.4.4.3.4
This bit is inverted and output onto the nSLCTIN output. A logic 1 on this bit selects the printer; a logic 0 means the
printer is not selected.
BIT 3 SELECTIN
5.4.4.3.5
The interrupt request enable bit when set to a high level may be used to enable interrupt requests from the
Parallel Port to the CPU due to a low to high transition on the nACK input. Refer to the description of the interrupt
under Operation, Interrupts.
BIT 4 ackIntEn - INTERRUPT REQUEST ENABLE
5.4.4.3.6
If mode=000 or mode=010, this bit has no effect and the direction is always out regardless of the state of this bit. In
all other modes, Direction is valid and a logic 0 means that the printer port is in output mode (write); a logic 1 means
that the printer port is in input mode (read).
BIT 5 DIRECTION
5.4.4.3.7
during a read are a low level, and cannot be written.
5.4.4.4
cFifo (Parallel Port Data FIFO)
ADDRESS OFFSET = 400h
Mode = 010
Bits 6 and 7
相關PDF資料
PDF描述
SP37E760 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP37E760-MC 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP8720 ECL two-modulus divider, with ECL10K compatible outputs
SP8720ADG ECL two-modulus divider, with ECL10K compatible outputs
SP8720BDG ECL two-modulus divider, with ECL10K compatible outputs
相關代理商/技術參數
參數描述
SP37E760-MT 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37R0FL 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor
SP38 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH
SP380 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NOR GATES
SP38003 制造商:SIPAT 制造商全稱:SIPAT 功能描述:SAW Filter Electrical Characteristic
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*