- 您現在的位置：買賣IC網 > PDF目錄365450 > S71WS512N80BAEZZ0 (Spansion Inc.) Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt PDF資料下載
參數資料
| 型號： | S71WS512N80BAEZZ0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| 中文描述： | 堆疊式多芯片產品（MCP）的閃存和移動存儲芯片的CMOS 1.8伏特 |
| 文件頁數： | 54/142頁 |
| 文件大小： | 1996K |
| 代理商： | S71WS512N80BAEZZ0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁
54
S29WSxxxN MirrorBit Flash Family For Multi-chip Products (MCP)
S71WS512NE0BFWZZ_00_ A1 June 28, 2004
A d v a n c e I n f o r m a t i o n
The reset command may be written between the sequence cycles in a program
command sequence before programming begins (prior to the third cycle). This re-
sets the bank to which the system was writing to the read mode. If the program
command sequence is written to a bank that is in the Erase Suspend mode, writ-
ing the reset command returns that bank to the erase-suspend-read mode. Once
programming begins, however, the device ignores reset commands until the op-
eration is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to the read mode. If a bank entered the autoselect mode while
in the Erase Suspend mode, writing the reset command returns that bank to the
erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command
returns the banks to the read mode (or erase-suspend-read mode if that bank
was in Erase Suspend and program-suspend-read mode if that bank was in Pro-
gram Suspend).
Note: If DQ1 goes high during a Write Buffer Programming operation, the system
must write the “Write to Buffer Abort Reset” command sequence to RESET the
device to reading array data. The standard RESET command will not work. See
Table 17 for details on this command sequence.
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
The "
Command Definition Summary
" section shows the address and data re-
quirements. The autoselect command sequence may be written to an address
within a bank that is either in the read or erase-suspend-read mode. The autose-
lect command may not be written while the device is actively programming or
erasing in the other bank. Autoselect does not support simultaneous operations
nor synchronous mode.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the bank address and the au-
toselect command. The bank then enters the autoselect mode. The system may
read at any address within the same bank any number of times without initiating
another autoselect command sequence. Read commands to other banks will re-
turn data from the array. Writes to other banks is not allowed. The following table
describes the address requirements for the various autoselect functions, and the
resulting data. BA represents the bank address. The device ID is read in three
cycles.
Table 17. Autoselect Addresses
Description
Manufacturer ID
Device ID, Word 1
Address
(BA) + 00h
(BA) + 01h
Read Data
0001h
227Eh
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512N80BAEZZ2 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAEZZ3 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ0 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ2 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ3 | Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512N80BAEZZ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAEZZ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
| S71WS512N80BAIZZ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and pSRAM CMOS 1.8 Volt |
發布緊急采購，3分鐘左右您將得到回復。