參數資料
型號： S29PL127J70
廠商： Spansion Inc.
英文描述： CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
中文描述： 3.0伏的CMOS只，同步讀/寫閃存與增強VersatileIO控制記憶
文件頁數： 68/106頁
文件大?。?/td> 1997K
代理商： S29PL127J70
66
S29PL127J/S29PL129J/S29PL064J/S29PL032J
31107A62 April 7, 2005
P R E L I M I N A R Y
operation. The program command sequence should be reinitiated once that bank
has returned to the read mode, to ensure data integrity. Note that the SecSi Sec-
tor, autoselect and CFI functions are unavailable when the SecSi Sector is
enabled.
Programming is allowed in any sequence and across sector boundaries.
A bit
cannot be programmed from “0” back to a “1.”
Attempting to do so may
cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate
the operation was successful. However, a succeeding read will show that the data
is still “0.” Only erase operations can convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program data to a bank faster
than using the standard program command sequence. The unlock bypass com-
mand sequence is initiated by first writing two unlock cycles. This is followed by
a third write cycle containing the unlock bypass command, 20h. That bank then
enters the unlock bypass mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The first cycle in this se-
quence contains the unlock bypass program command, A0h; the second cycle
contains the program address and data. Additional data is programmed in the
same manner. This mode dispenses with the initial two unlock cycles required in
the standard program command sequence, resulting in faster total programming
time.
Table 21
shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (See Table 22)
The device offers accelerated program operations through the WP#/ACC pin.
When the system asserts V
HH
on the WP#/ACC pin, the device automatically en-
ters the Unlock Bypass mode. The system may then write the two-cycle Unlock
Bypass program command sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation.
Note that the WP#/ACC pin must not
be at V
HH
any operation other than accelerated programming, or device damage
may result. In addition, the WP#/ACC pin must not be left floating or uncon-
nected; inconsistent behavior of the device may result.
4 illustrates the algorithm for the program operation. Refer to the "
Erase/Program
Operations
" section table in the AC Characteristics section for parameters, and
Figure 14
for timing diagrams.
相關PDF資料
PDF描述
S2A_1 2.0 AMPS. Surface Mount Rectifiers
S2K 2.0 AMPS. Surface Mount Rectifiers
S2M 2.0 AMPS. Surface Mount Rectifiers
S2A 2.0 AMPS. Surface Mount Rectifiers
S2B 2.0 AMPS. Surface Mount Rectifiers
相關代理商/技術參數
參數描述
S29PL127J70BAI000 功能描述:閃存 128Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL127J70BAI020 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 64FBGA - Trays
S29PL127J70BFI000 制造商:Spansion 功能描述:SPZS29PL127J70BFI000 POWER MOSFET 30 V, 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 80FBGA - Trays
S29PL127J70TAI130 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays
S29PL127J70TFI130 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*