- 您現在的位置：買賣IC網 > PDF目錄25635 > MD80C52EXXX-16SBD (ATMEL CORP) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD80C52EXXX-16SBD |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, CERAMIC, DIP-40 |
| 文件頁數： | 190/198頁 |
| 文件大?。?/td> | 4822K |
| 代理商： | MD80C52EXXX-16SBD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁當前第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁
91
8111C–MCU Wireless–09/09
AT86RF231
8.4
Energy Detection (ED)
The Energy Detection (ED) module is characterized by:
85 unique energy levels defined
1 dB resolution
8.4.1
Overview
The receiver ED measurement is used by the network layer as part of a channel selection algo-
rithm. It is an estimation of the received signal power within the bandwidth of an IEEE 802.15.4
channel. No attempt is made to identify or decode signals on the channel. The ED value is cal-
culated by averaging RSSI values over eight symbols (128 s).
For High Data Rate Modes the automated ED measurement duration is reduced to 32 s, refer
to Section 11.3 “High Data Rate Modes” on page 137. For manually initiated ED measurements
in these modes the measurement period is still 128 s as long as the receiver is in RX_ON state.
8.4.2
Measurement Description
There are two ways to initiate an ED measurement:
Manually, by writing an arbitrary value to register 0x07 (PHY_ED_LEVEL), or
Automatically, after detection of a valid SHR of an incoming frame.
For manually initiated ED measurements the radio transceiver needs to be in one of the states
RX_ON or BUSY_RX state. The end of the ED measurement is indicated by an interrupt
IRQ_4 (CCA_ED_DONE).
An automated ED measurement is started if an SHR is detected. The end of the automated
measurement is not signaled by an interrupt.
The measurement result is stored after t
TR26 = 140 s (128 s measurement duration and pro-
cessing delay) in register 0x07 (PHY_ED_LEVEL).
Thus by using Basic Operating Mode, a valid ED value from the currently received frame is
accessible 108 s after IRQ_2 (RX_START) and remains valid until a new RX_START interrupt
is generated by the next incoming frame or until another ED measurement is initiated.
By using the Extended Operating Mode, it is recommended to mask IRQ_2 (RX_START), thus
the interrupt cannot be used as timing reference. A successful frame reception is signalized by
interrupt IRQ_3 (TRX_END). The minimum time span between a TRX_END interrupt and a fol-
lowing SFD detection is t
TR27 = 96 s due to the le ngth of the SHR. In cluding th e ED
measurement time, the ED value needs to be read within 224 s after the TRX_END interrupt;
otherwise, it could be overwritten by the result of the next measurement cycle. This is important
for time critical applications or if interrupt IRQ_2 (RX_START) is not used to indicate the recep-
tion of a frame.
Note, it is not recommended to manually initiate an ED measurement when using the Extended
Operating Mode.
The values of the register 0x07 (PHY_ED_LEVEL) are:
Table 8-7.
Register Bit PHY_ED_LEVEL Interpretation
PHY_ED_LEVEL
Description
0xFF
Reset value
0x00.... 0x54
ED measurement result of the last ED measurement
相關PDF資料 |
PDF描述 |
|---|---|
| MD80C52EXXX-20SB | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40 |
| MQ80C32E-36SC | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| MR80C52XXX-20:R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44 |
| MQ80C32E-30/883 | 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 |
| MR80C52CXXX-16/883R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C862 | 制造商:Intel 功能描述:PROCESSOR:MICRO-PROCESSOR |
| MD80C86-2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C86-2/883 | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:CPU 16BILT 5V CMOS 8MHZ 40CDIP - Bulk |
| MD80C86-2/B | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。