參數資料
型號： LAN8187
廠商： SMSC Corporation
英文描述： High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
中文描述： 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能
文件頁數： 31/66頁
文件大?。?/td> 545K
代理商： LAN8187
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
SMSC LAN8187/LAN8187I
31
Revision 0.6 (02-24-06)
DATASHEET
The RXD3 pin is latched on the rising edge of the internal reset (nreset) to select the mode. The
system designer must float the RXD3 pin for nINT mode or pull-low with an external resistor (see
Table 4.3, “Boot Strapping Configuration Resistors,” on page 32
) to VSS to set the device in
TX_ER/TXD4 mode. The default setting is high (nINT mode).
Note:
For VDDIO operation below +2.5V, SMSC recommends designs add external strapping
resistors in addition the internal strapping resistors to ensure proper strapped operation.
4.11
PHY Address Strapping and LED Output Polarity Selection
The PHY ADDRESS bits are latched on the rising edge of the internal reset (nreset). The 5-bit address
word[0:4] is input on the LED1, LED2, LED3, LED4, GPO1 output pins. The default setting is all high
5'b1_1111.
The address lines are strapped as defined in the diagram below. The LED outputs will automatically
change polarity based on the presence of an external pull-down resistor. If the LED pin is pulled high
(by an internal 100K pull-up resistor) to select a logical high PHY address, then the LED output will
be active low. If the LED pin is pulled low (by an external pull-down resistor (see
Table 4.3, “Boot
Strapping Configuration Resistors,” on page 32
) to select a logical low PHY address, the LED output
will then be an active high output.
To set the PHY address on the LED pins without LEDs or on the GPO1 or CRS pin, float the pin to
set the address high or pull-down the pin with an external resistor (see
Table 4.3, “Boot Strapping
Configuration Resistors,” on page 32
) to GND to set the address low. See the figure below:
Figure 4.5 PHY Address Strapping on LED’s
4.12
Variable Voltage I/O
The Digital I/O pins on the LAN8187/LAN8187I are variable voltage to take advantage of low power
savings from shrinking technologies. These pins can operate from a low I/O voltage of +1.6V up to
+3.6V. Due to this low voltage feature addition, the system designer needs to take consideration as
for two aspects of their design. Boot strapping configuration and I/O voltage stability.
LED1-LED4
~270 ohms
Phy Address = 0
LED output = active high
~10K ohms
~270 ohms
LED1-LED4
VDD
Phy Address = 1
LED output = active low
相關PDF資料
PDF描述
LAN83C175 Ethernet CARDBUS Integrated Controller With Modem Support
LAN83C180 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C185 HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
LAN83C183-JD FAST ETHERNET PHYSICAL LAYER DEVICE
LAN83C180TQFP 10/100 FAST ETHERNET PHY TRANSCEIVER
相關代理商/技術參數
參數描述
LAN8187_06 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM
LAN8187I 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
LAN8187I-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8187-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN83C171 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*