參數資料
型號: LAN8187
廠商: SMSC Corporation
英文描述: High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
中文描述: 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能
文件頁數: 15/66頁
文件大小: 545K
代理商: LAN8187
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
SMSC LAN8187/LAN8187I
15
Revision 0.6 (02-24-06)
DATASHEET
MODE2
I
PHY Operating Mode Bit 2:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 51
, for
the MODE options.
MODE1
I
PHY Operating Mode Bit 1:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 51
, for
the MODE options.
MODE0
I
PHY Operating Mode Bit 0:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 51
, for
the MODE options.
TEST1
I
Test Mode Select 1:
Must be left floating.
TEST0
I
Test Mode Select 0:
Must be left floating.
REG_EN
I
Regulator Enable
: Internal +1.8V regulator enable:
VDDIO – Enables internal regulator.
VSS– Disables internal regulator.
AMDIX_EN
I
HP Auto-MDIX Enable:
Auto-MDIX mode enable.
+3.3V – Enables HP Auto-MDIX.
0V – Disables HP Auto-MDIX
CH_SELECT
I
Channel Select:
With Auto-MDIX disabled above,
VDDIO – Enables HP Auto-MDIX.
0V – Disables HP Auto-MDIX
GPO0/MII
I/O
General Purpose Output 0 –
General Purpose Output signal.
Driven by bits in registers 27 and 31.
MII –
MII/RMII mode selection is latched on the rising edge of
the internal reset (nreset) based on the following strapping:
Float the GPO0 pin for MII mode or pull-high with an external
Pull-up resistor (see
Table 4.3, “Boot Strapping Configuration
Resistors,” on page 32
) to VDDIO to set the device in RMII
mode.
Note:
See
Section 4.6.3, "MII vs. RMII Configuration," on
page 26
for more details.
a.On nRST transition high, the PHY latches the state of the configuration pins in this table.
Table 3.5 General Signals
SIGNAL NAME
TYPE
DESCRIPTION
nINT
I/O
LAN Interrupt
– Active Low output. Place a pull-up external
resistor (see
Table 4.3, “Boot Strapping Configuration Resistors,”
on page 32
) to VCC 3.3V.
Notes:
This signal is mux’d with TX_ER/TXD4
See
Section 4.10, "(TX_ER/TXD4)/nINT Strapping," on
page 30
for additional details on Strapping options.
nRST
I
External Reset
– input of the system reset. This signal is active
LOW.
Table 3.4 Boot Strap Configuration Inputs
a
SIGNAL NAME
TYPE
DESCRIPTION
相關PDF資料
PDF描述
LAN83C175 Ethernet CARDBUS Integrated Controller With Modem Support
LAN83C180 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C185 HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
LAN83C183-JD FAST ETHERNET PHYSICAL LAYER DEVICE
LAN83C180TQFP 10/100 FAST ETHERNET PHY TRANSCEIVER
相關代理商/技術參數
參數描述
LAN8187_06 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM
LAN8187I 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
LAN8187I-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8187-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN83C171 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller