參數資料
型號： LAN8187
廠商： SMSC Corporation
英文描述： High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
中文描述： 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能
文件頁數： 26/66頁
文件大?。?/td> 545K
代理商： LAN8187
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
Revision 0.6 (02-24-06)
26
SMSC LAN8187/LAN8187I
DATASHEET
It uses LVCMOS signal levels, compatible with common digital CMOS ASIC processes
The RMII includes 6 interface signals with one of the signals being optional:
transmit data - TXD[1:0]
transmit strobe - TX_EN
receive data - RXD[1:0]
receive error - RX_ER (Optional)
carrier sense - CRS_DV
Reference Clock - CLKIN/XTAL1 (RMII references usually define this signal as REF_CLK)
4.6.2.1
Reference Clock
The Reference Clock - CLKIN, is a continuous clock that provides the timing reference for CRS_DV,
RXD[1:0], TX_EN, TXD[1:0], and RX_ER. The Reference Clock is sourced by the MAC or an external
source. Switch implementations may choose to provide REF_CLK as an input or an output depending
on whether they provide a REF_CLK output or rely on an external clock distribution device.
The “Reference Clock” frequency must be 50 MHz +/- 50 ppm with a duty cycle between 35% and
65% inclusive. The SMSC LAN8187/LAN8187I uses the “Reference Clock” as the network clock such
that no buffering is required on the transmit data path. The SMSC LAN8187/LAN8187I will recover the
clock from the incoming data stream, the receiver will account for differences between the local
REF_CLK and the recovered clock through use of sufficient elasticity buffering. The elasticity buffer
does not affect the Inter-Packet Gap (IPG) for received IPGs of 36 bits or greater. To tolerate the clock
variations specified here for Ethernet MTUs, the elasticity buffer shall tolerate a minimum of +/-10 bits.
4.6.2.2
CRS_DV - Carrier Sense/Receive Data Valid
The CRS_DV is asserted by the LAN8187/LAN8187I when the receive medium is non-idle. CRS_DV
is asserted asynchronously on detection of carrier due to the criteria relevant to the operating mode.
That is, in 10BASE-T mode, when squelch is passed or in 100BASE-X mode when 2 non-contiguous
zeroes in 10 bits are detected, carrier is said to be detected.
Loss of carrier shall result in the deassertion of CRS_DV synchronous to the cycle of REF_CLK which
presents the first di-bit of a nibble onto RXD[1:0] (i.e. CRS_DV is deasserted only on nibble
boundaries). If the LAN8187/LAN8187I has additional bits to be presented on RXD[1:0] following the
initial deassertion of CRS_DV, then the LAN8187/LAN8187I shall assert CRS_DV on cycles of
REF_CLK which present the second di-bit of each nibble and de-assert CRS_DV on cycles of
REF_CLK which present the first di-bit of a nibble. The result is: Starting on nibble boundaries
CRS_DV toggles at 25 MHz in 100Mb/s mode and 2.5 MHz in 10Mb/s mode when CRS ends before
RX_DV (i.e. the FIFO still has bits to transfer when the carrier event ends.) Therefore, the MAC can
accurately recover RX_DV and CRS.
During a false carrier event, CRS_DV shall remain asserted for the duration of carrier activity. The data
on RXD[1:0] is considered valid once CRS_DV is asserted. However, since the assertion of CRS_DV
is asynchronous relative to REF_CLK, the data on RXD[1:0] shall be “00” until proper receive signal
decoding takes place.
4.6.3
MII vs. RMII Configuration
The LAN8187/LAN8187I must be configured to support the MII or RMII bus for connectivity to the
MAC. This configuration is done through the GPO0/MII pin.
MII or RMII mode selection is latched on the rising edge of the internal reset (nreset) based on the
strapping of the GPO0/MII pin. To select MII mode, float the GPO0/MII pin. To select RMII mode, pull-
high with an external resistor (see
Table 4.3, “Boot Strapping Configuration Resistors,” on page 32
) to
VDD33.
相關PDF資料
PDF描述
LAN83C175 Ethernet CARDBUS Integrated Controller With Modem Support
LAN83C180 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C185 HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
LAN83C183-JD FAST ETHERNET PHYSICAL LAYER DEVICE
LAN83C180TQFP 10/100 FAST ETHERNET PHY TRANSCEIVER
相關代理商/技術參數
參數描述
LAN8187_06 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM
LAN8187I 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
LAN8187I-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8187-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN83C171 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*