- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN8187 (SMSC Corporation) High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX PDF資料下載
參數資料
| 型號： | LAN8187 |
| 廠商： | SMSC Corporation |
| 英文描述： | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| 中文描述： | 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能 |
| 文件頁數： | 23/66頁 |
| 文件大?。?/td> | 545K |
| 代理商： | LAN8187 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
4.3.8
SMSC LAN8187/LAN8187I
23
Revision 0.6 (02-24-06)
DATASHEET
Receiver Errors
During a frame, unexpected code-groups are considered receive errors. Expected code groups are the
DATA set (0 through F), and the /T/R/ (ESD) symbol pair. When a receive error occurs, the RX_ER
signal is asserted and arbitrary data is driven onto the RXD[3:0] lines. Should an error be detected
during the time that the /J/K/ delimiter is being decoded (bad SSD error), RX_ER is asserted true and
the value ‘1110’ is driven onto the RXD[3:0] lines. Note that the Valid Data signal is not yet asserted
when the bad SSD error occurs.
4.3.9
100M Receive Data Across the MII/RMII Interface
In MII mode, the 4-bit data nibbles are sent to the MII block. These data nibbles are clocked to the
controller at a rate of 25MHz. The controller samples the data on the rising edge of RX_CLK. To ensure
that the setup and hold requirements are met, the nibbles are clocked out of the PHY on the falling
edge of RX_CLK. RX_CLK is the 25MHz output clock for the MII bus. It is recovered from the received
data to clock the RXD bus. If there is no received signal, it is derived from the system reference clock
(CLKIN).
When tracking the received data, RX_CLK has a maximum jitter of 0.8ns (provided that the jitter of the
input clock, CLKIN, is below 100ps).
In RMII mode, the 2-bit data nibbles are sent to the RMII block. These data nibbles are clocked to the
controller at a rate of 50MHz. The controller samples the data on the rising edge of CLKIN/XTAL1
(REF_CLK). To ensure that the setup and hold requirements are met, the nibbles are clocked out of
the PHY on the falling edge of CLKIN/XTAL1 (REF_CLK).
4.4
10Base-T Transmit
Data to be transmitted comes from the MAC layer controller. The 10Base-T transmitter receives 4-bit
nibbles from the MII at a rate of 2.5MHz and converts them to a 10Mbps serial data stream. The data
stream is then Manchester-encoded and sent to the analog transmitter, which drives a signal onto the
twisted pair via the external magnetics.
The 10M transmitter uses the following blocks:
MII (digital)
TX 10M (digital)
10M Transmitter (analog)
10M PLL (analog)
4.4.1
10M Transmit Data Across the MII/RMII Interface
The MAC controller drives the transmit data onto the TXD BUS. For MII, when the controller has driven
TX_EN high to indicate valid data, the data is latched by the MII block on the rising edge of TX_CLK.
The data is in the form of 4-bit wide 2.5MHz data.
In order to comply with legacy 10Base-T MAC/Controllers, in Half-duplex mode the PHY loops back
the transmitted data, on the receive path. This does not confuse the MAC/Controller since the COL
signal is not asserted during this time. The PHY also supports the SQE (Heartbeat) signal. See
Section
5.4.2, "Collision Detect," on page 49
, for more details.
For RMII, TXD[1:0] shall transition synchronously with respect to REF_CLK. When TX_EN is asserted,
TXD[1:0] are accepted for transmission by the LAN8187/LAN8187I. TXD[1:0] shall be “00” to indicate
idle when TX_EN is deasserted. Values of TXD[1:0] other than “00” when TX_EN is deasserted are
reserved for out-of-band signalling (to be defined). Values other than “00” on TXD[1:0] while TX_EN is
deasserted shall be ignored by the LAN8187/LAN8187I.TXD[1:0] shall provide valid data for each
REF_CLK period while TX_EN is asserted.
相關PDF資料 |
PDF描述 |
|---|---|
| LAN83C175 | Ethernet CARDBUS Integrated Controller With Modem Support |
| LAN83C180 | 10/100 FAST ETHERNET PHY TRANSCEIVER |
| LAN83C185 | HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER |
| LAN83C183-JD | FAST ETHERNET PHYSICAL LAYER DEVICE |
| LAN83C180TQFP | 10/100 FAST ETHERNET PHY TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN8187_06 | 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM |
| LAN8187I | 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN8187I-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8187-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN83C171 | 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller |
發布緊急采購，3分鐘左右您將得到回復。