- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN8187 (SMSC Corporation) High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX PDF資料下載
參數資料
| 型號： | LAN8187 |
| 廠商： | SMSC Corporation |
| 英文描述： | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| 中文描述： | 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能 |
| 文件頁數： | 16/66頁 |
| 文件大?。?/td> | 545K |
| 代理商： | LAN8187 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
Revision 0.6 (02-24-06)
16
SMSC LAN8187/LAN8187I
DATASHEET
CLKIN/XTAL1
I
Clock Input
– 25 Mhz or 50 MHz external clock or crystal input.
In MII mode, this signal is the 25 MHz reference input clock
In RMII mode, this signal is the 50 MHz reference input clock
which is typically also driven to the RMII compliant Ethernet MAC
clock input.
Note:
See
Section 4.10, "(TX_ER/TXD4)/nINT Strapping," on
page 30
for additional details on Strapping options.
XTAL2
O
Clock Output
– 25 MHz crystal output.
Note:
See
Section 4.10, "(TX_ER/TXD4)/nINT Strapping," on
page 30
for additional details on Strapping options.
Also, float this pin if using an external clock being
driven through CLKIN/XTAL1
GPO2
O
General Purpose Output 2 –
General Purpose Output signal
Driven by bits in registers 27 and 31.
GPO1
O
General Purpose Output 1 –
General Purpose Output signal
Driven by bits in registers 27 and 31. This signal is mux’d with
PHYAD4.
GPO0/MII
I/O
General Purpose Output 0 –
General Purpose Output signal.
Driven by bits in registers 27 and 31.
MII –
MII/RMII mode selection is latched on the rising edge of
the internal reset (nreset) based on the following strapping:
Float the GPO0 pin for MII mode or pull-high with an external
(see
Table 4.3, “Boot Strapping Configuration Resistors,” on
page 32
) resistor to VDDIO to set the device in RMII mode.
Note:
See
Section 4.6.3, "MII vs. RMII Configuration," on
page 26
for more details.
Table 3.6 10/100 Line Interface
SIGNAL NAME
TYPE
DESCRIPTION
TXP
AO
Transmit Data
: 100Base-TX or 10Base-T differential transmit
outputs to magnetics.
TXN
AO
Transmit Data
: 100Base-TX or 10Base-T differential transmit
outputs to magnetics.
RXP
AI
Receive Data
: 100Base-TX or 10Base-T differential receive
inputs from magnetics.
RXN
AI
Receive Data
: 100Base-TX or 10Base-T differential receive
inputs from magnetics.
Table 3.7 Analog References
SIGNAL NAME
TYPE
DESCRIPTION
EXRES1
AI
Connects to reference resistor of value 12.4K-Ohm, 1%
connected as described in the Analog Layout Guidelines.
Table 3.5 General Signals (continued)
SIGNAL NAME
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| LAN83C175 | Ethernet CARDBUS Integrated Controller With Modem Support |
| LAN83C180 | 10/100 FAST ETHERNET PHY TRANSCEIVER |
| LAN83C185 | HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER |
| LAN83C183-JD | FAST ETHERNET PHYSICAL LAYER DEVICE |
| LAN83C180TQFP | 10/100 FAST ETHERNET PHY TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN8187_06 | 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM |
| LAN8187I | 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN8187I-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8187-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN83C171 | 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller |
發布緊急采購，3分鐘左右您將得到回復。