- 您現在的位置：買賣IC網 > PDF目錄383236 > L6238 (意法半導體) Sensorless Spindle Motor Driver(無傳感器主軸電機驅動器) PDF資料下載
參數資料
| 型號： | L6238 |
| 廠商： | 意法半導體 |
| 英文描述： | Sensorless Spindle Motor Driver(無傳感器主軸電機驅動器) |
| 中文描述： | 傳感器主軸電機驅動器（無傳感器主軸電機驅動器） |
| 文件頁數： | 15/35頁 |
| 文件大?。?/td> | 383K |
| 代理商： | L6238 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
4.2 Counter Section
Figure 11 is a block diagram of the counter sec-
tion of the PLLalong with the phase detector.
The phase detector provides up and down signals
that are used to control the directionand counting
period of two 8 bit counters. Two counters are
used to provide both coarse and fine phase error
information. The coarse counter operates to bring
the phase error into a finite window, while the fine
counter with it’s higher resolution controls the
phasejitter to typically5
μ
s.
As an example,during a positive phase measure-
ment, the counters are reset to 10000000 which
is the middle of their measurement range corre-
spondingto zero degrees phase error. The falling
edge of Fref, in conjunction with the ”up” signal,
causes the fine counter to then start counting up.
The coarse counter is inhibitedby the fine counter
until the fine counter has reached it’s maximum
count. The falling edge of Fmtr causes the count-
ers to stop counting and the bits in the fine and
course counters are then latched into their re-
spective latches. The counters are then reset to
10000000in anticipation of the next phase meas-
urement.
The operation of the counter section during spin-
up and phase lock can be described in three
phases:
1)
Initial Spin-Up
- At start-up the PLL will inher-
entlybring the motorspeed ”in line” with the refer-
ence frequency.The phase detector is initialized
at power up to force the countersto start counting
up.
Since there will be many more Fref. vs Fmtr fall-
ing edges at start-up, the width of the ”up” pulse
will be wide. The fine counter will reach it’s maxi-
mum count and send an enable pulse to the
coarse counter causing it to start counting. After
127 counts, the coarse counter also reaches it’s
maximum count. At the end of the ”up” pulse, it’s
rising edge loads the outputs of the Coarse and
Fine counters into corresponding latches. Thus
the latches are updated once-per-rev with a bi-
nary number that corresponds to the measured
phase error. This count will be converted via a
Digital to Analog Convertors (DAC) into a speed
Command Voltage, which at start-up will be the
maximum as set by the ILIM SET voltage.
2)
Overshoot
- As the motor speed increases
close to the reference, the coarse counter comes
out of compliance and decreasesit’s count as the
phase difference becomes smaller. The fine
counter then takes over when the phase is in a
certain range. A certain amount of phase over-
shoot will take place as the motor passes though
zero phase difference due to the closed loop sys-
tem responsecharacteristics.
This will cause the counters to count down to
”slow” the motor down until the phase difference
is minimal.
Figure11:
LogicBlock Diagram.
L6238
15/35
相關PDF資料 |
PDF描述 |
|---|---|
| L6239 | 12V Disk Drive Spindle Driver(12V磁盤驅動主軸驅動器) |
| L6242 | VOICE COIL MOTOR DRIVER |
| L6243 | VOICE COIL MOTOR DRIVER |
| L6243D | VOICE COIL MOTOR DRIVER |
| L6243DS | VOICE COIL MOTOR DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6238S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:12V SENSORLESS SPINDLE MOTOR CONTROLLER |
| L6238SQA | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:12V SENSORLESS SPINDLE MOTOR CONTROLLER |
| L6238SQT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:12V SENSORLESS SPINDLE MOTOR CONTROLLER |
| L6239 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L623C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:THYRISTOR MODULE|BRIDGE|HALF-CNTLD|CA|280V V(RRM)|46A I(T) |
發布緊急采購，3分鐘左右您將得到回復。