- 您現在的位置：買賣IC網 > PDF目錄1922 > FUSB2805MLX (Fairchild Semiconductor)TXRX USB2.0 HS OTG ULPI 32MLP PDF資料下載
參數資料
| 型號： | FUSB2805MLX |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 46/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX USB2.0 HS OTG ULPI 32MLP |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | FUSB2805MLXFSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁
2008 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FUSB2805 Rev. 1.0.3
6
F
USB2
8
0
5
—
USB2
.0
High
-S
pee
d
OTG
Tra
nsc
e
iv
e
rw
ith
UL
P
I
Inter
fac
e
OTG Module
The OTG module contains several sub-blocks that
provide the functionality required by the USB On-The-
Go Rev. 1.3 supplement. Specifically, it provides the
following circuits:
ID detector to sense the ID pin of the micro-USB
cable. The ID pin dictates which device is initially
configured as the host and which is configured as
the peripheral.
VBUS comparators to determine the VBUS voltage
level. This is required for Host Negotiation Protocol
(HNP) and Session Request Protocol (SRP).
Resistors to temporarily charge and discharge
VBUS. This is required for SRP.
ID Detector
Detects which end of the mini-USB
(or micro-USB) cable
is plugged in. The ID detector must first be enabled by
setting the ID_PULLUP register bit to 1b. If the
FUSB2805 senses a value on ID different from the
previously reported value, an RX CMD status update is
sent to the USB link controller or an interrupt is asserted.
If the micro-B end of the cable is plugged in, the
FUSB2805 reports that ID_GND is logic 1 and the USB
link controller changes to peripheral mode.
If the micro-A end of the cable is plugged in, the
FUSB2805 reports that ID_GND is logic 0 and the USB
link controller changes to host mode.
The ID pin has a weak pull-
up resistor (400kΩ) to avoid
floating conditions. This resistor is connected when
ID_PULLUP register bit is 0. If the application does not
use the ID pin, tie this pin to VCC3V3.
VBUS Comparators
The
FUSB2805
provides
three
comparators
for
Table 12. The comparators are as follows:
VBUS-Valid Comparator
This comparator is used by an A-device (or host) to
determine whether or not the voltage on
VBUS is at a
valid level for operation. The minimum threshold for
the
VBUS valid comparator is 4.4 V. Any voltage on
VBUS below this threshold is considered a fault.
During power-up, the comparator output is ignored.
Session-Valid Comparator
The session-valid comparator is a TTL-level input that
determines when
VBUS is high enough for a session
to start. Both the A-device and the B-device use this
comparator to detect when a session is being started.
The A-device also uses this comparator to determine
when a session is completed. The session valid
threshold is between 0.8 V to 2.0 V.
Session-End Comparator
The session-end comparator determines when
VBUS
is below the B-device session-end threshold of 0.2 V
to 0.8 V. The B-device uses this threshold to
determine when a session has ended.
SRP Charge and Discharge Resistors
The FUSB2805 provides on-chip resistors for short-term
charging and discharging of
VBUS. These are used by
the B-device to request a session, prompting the A-
device to restore
VBUS power. First, the B-device
verifies that
VBUS is fully discharged from the previous
session by setting the DISCHARGE_VBUS register bit
to 1b and waiting for SESS_END to be 1b. Then the B-
device charges
VBUS by setting the CHARGE_VBUS
register bit to 1b. The A-device detects that
VBUS is
charged above the session-valid threshold and starts a
session by turning on
VBUS power.
Analog Reference Module
The analog reference module provides stable internal
voltage and current references for biasing internal
analog circuitry. This module requires an accurate
external reference resistor. A value of 12 k
1%
resistor is required between the RREF pin and GND.
相關PDF資料 |
PDF描述 |
|---|---|
| FXLA2203UMX | TRANSLATOR LEVEL DUAL 24UMLP |
| GAL16V8D-15LJN | SPLD 62.5MHZ EECMOS 20 PLCC |
| GAL18V10B-20LP | IC GAL 10OUT MACROCELL 7.5NS 20 |
| GAL22V10D-25LJ | IC SPLD 3.3V 28-PLCC |
| GH65C11-C-PD | OPTO ENCODER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FUSCA REF BOARD | 制造商:TDK 功能描述:REFERENCE BOARD FUSCA 2.4GHZ |
| FUSCAREFBOARD | 制造商:Antenova 功能描述:Reference Board Fusca 2.4GHz |
| FUSE | 功能描述:保險絲 Fuse, Fiber 20A 600V Lot Qty 5 RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| FUSE 25A ATC | 制造商:American Technical Ceramics Corp 功能描述: 制造商:ATC 功能描述: |
| FUSE KIT D | 制造商:COOPER BUSSMANN 功能描述:BUSSMANN FUSE KIT |
發布緊急采購，3分鐘左右您將得到回復。