參數資料
型號： DSPIC30F5015-30I/PT
廠商： Microchip Technology
文件頁數： 5/129頁
文件大小： 0K
描述： IC DSPIC MCU/DSP 66K 64TQFP
產品培訓模塊： dsPIC30F Quadrature Encoder Interface
Serial Communications using dsPIC30F CAN
Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
標準包裝： 160
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 30 MIP
連通性： CAN，I²C，SPI，UART/USART
外圍設備： 高級欠壓探測/復位，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 52
程序存儲器容量： 66KB（22K x 24）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 1K x 8
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 托盤
產品目錄頁面： 651 (CN2011-ZH PDF)
配用： XLT64PT5-ND - SOCKET TRAN ICE 64MQFP/TQFP
AC164319-ND - MODULE SKT MPLAB PM3 64TQFP
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
其它名稱： DSPIC30F501530IPT
dsPIC30F5015/5016
DS70149D-page 102
2008 Microchip Technology Inc.
15.11 PWM Output and Polarity Control
There are three device Configuration bits associated
with the PWM module that provide PWM output pin
control:
HPOL Configuration bit
LPOL Configuration bit
PWMPIN Configuration bit
These three bits in the FBORPOR Configuration
Registers”) work in conjunction with the four PWM
Enable bits (PWMEN<4:1>) located in the PWMCON1
SFR. The Configuration bits and PWM enable bits
ensure that the PWM pins are in the correct states after
a device Reset occurs. The PWMPIN configuration
fuse allows the PWM module outputs to be optionally
enabled on a device Reset. If PWMPIN = 0, the PWM
outputs will be driven to their inactive states at Reset. If
PWMPIN = 1 (default), the PWM outputs will be
tri-stated. The HPOL bit specifies the polarity for the
PWMxH outputs, whereas the LPOL bit specifies the
polarity for the PWMxL outputs.
15.11.1
OUTPUT PIN CONTROL
The PENxH and PENxL control bits in the PWMCON1
SFR enable each high PWM output pin and each low
PWM output pin, respectively. If a particular PWM out-
put pin is not enabled, it is treated as a general purpose
I/O pin.
15.12 PWM FAULT Pins
There are two Fault pins (FLTA and FLTB) associated
with the PWM module. When asserted, these pins can
optionally drive each of the PWM I/O pins to a defined
state.
15.12.1
FAULT PIN ENABLE BITS
The FLTACON and FLTBCON SFRs each have 4 con-
trol bits that determine whether a particular pair of
PWM I/O pins is to be controlled by the Fault input pin.
To enable a specific PWM I/O pin pair for Fault over-
rides, the corresponding bit should be set in the
FLTACON or FLTBCON register.
If all enable bits are cleared in the FLTACON or
FLTBCON registers, then the corresponding Fault input
pin has no effect on the PWM module and the pin may
be used as a general purpose interrupt or I/O pin.
15.12.2
FAULT STATES
The FLTACON and FLTBCON Special Function Regis-
ters have 8 bits each that determine the state of each
PWM I/O pin when it is overridden by a Fault input.
When these bits are cleared, the PWM I/O pin is driven
to the inactive state. If the bit is set, the PWM I/O pin
will be driven to the active state. The active and inactive
states are referenced to the polarity defined for each
PWM I/O pin (HPOL and LPOL polarity control bits).
A special case exists when a PWM module I/O pair is
in the Complementary mode and both pins are
programmed to be active on a Fault condition. The
PWMxH pin always has priority in the Complementary
mode, so that both I/O pins cannot be driven active
simultaneously.
15.12.3
FAULT PIN PRIORITY
If both Fault input pins have been assigned to control a
particular PWM I/O pin, the Fault state programmed for
the Fault A input pin will take priority over the Fault B
input pin.
15.12.4
FAULT INPUT MODES
Each of the Fault input pins has two modes of
operation:
Latched Mode: When the Fault pin is driven low,
the PWM outputs will go to the states defined in
the FLTACON/FLTBCON register. The PWM
outputs will remain in this state until the Fault pin
is driven high and the corresponding interrupt flag
has been cleared in software. When both of these
actions have occurred, the PWM outputs will
return to normal operation at the beginning of the
next PWM cycle or half-cycle boundary. If the
interrupt flag is cleared before the Fault condition
ends, the PWM module will wait until the Fault pin
is no longer asserted, to restore the outputs.
Cycle-by-Cycle Mode: When the Fault input pin
is driven low, the PWM outputs remain in the
defined Fault states for as long as the Fault pin is
held low. After the Fault pin is driven high, the
PWM outputs return to normal operation at the
beginning of the following PWM cycle or
half-cycle boundary.
The operating mode for each Fault input pin is selected
using the FLTAM and FLTBM control bits in the
FLTACON and FLTBCON Special Function Registers.
Each of the Fault pins can be controlled manually in
software.
Note:
The
Fault
pin
logic
can
operate
independent of the PWM logic. If all the
enable bits in the FLTACON/FLTBCON
registers are cleared, then the Fault pin(s)
could be used as general purpose
interrupt pin(s). Each Fault pin has an
interrupt vector, interrupt flag bit and
interrupt priority bits associated with it.
相關PDF資料
PDF描述
DSPIC30F6010-20E/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6010A-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-30I/PF IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6014-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC33EP512MU814-I/PL IC DSC 16BIT 512KB 144LQFP
相關代理商/技術參數
參數描述
dsPIC30F5015T-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F5015T-20I/PT 功能描述:IC DSPIC MCU/DSP 66K 64TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
dsPIC30F5015T-30I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F5016-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F5016-20I/PT 功能描述:IC DSPIC MCU/DSP 66K 80TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*