參數資料
型號： DSPIC30F5015-30I/PT
廠商： Microchip Technology
文件頁數： 25/129頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 66K 64TQFP
產品培訓模塊： dsPIC30F Quadrature Encoder Interface
Serial Communications using dsPIC30F CAN
Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
標準包裝： 160
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 30 MIP
連通性： CAN，I²C，SPI，UART/USART
外圍設備： 高級欠壓探測/復位，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 52
程序存儲器容量： 66KB（22K x 24）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 1K x 8
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 托盤
產品目錄頁面： 651 (CN2011-ZH PDF)
配用： XLT64PT5-ND - SOCKET TRAN ICE 64MQFP/TQFP
AC164319-ND - MODULE SKT MPLAB PM3 64TQFP
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
其它名稱： DSPIC30F501530IPT
dsPIC30F5015/5016
DS70149D-page 120
2008 Microchip Technology Inc.
18.3.4
TRANSMIT INTERRUPT
The transmit interrupt flag (U1TXIF) is located in the
corresponding Interrupt Flag register.
The transmitter generates an edge to set the UxTXIF
bit. The condition for generating the interrupt depends
on UTXISEL control bit:
a) If UTXISEL = 0, an interrupt is generated when
a word is transferred from the Transmit buffer to
the Transmit Shift register (UxTSR). This implies
that the transmit buffer has at least one empty
word.
b) If UTXISEL = 1, an interrupt is generated when
a word is transferred from the Transmit buffer to
the Transmit Shift register (UxTSR) and the
Transmit buffer is empty.
Switching between the two interrupt modes during
operation is possible and sometimes offers more
flexibility.
18.3.5
TRANSMIT BREAK
Setting the UTXBRK bit (UxSTA<11>) will cause the
UxTX line to be driven to logic ‘0’. The UTXBRK bit
overrides all transmission activity. Therefore, the user
should generally wait for the transmitter to be Idle
before setting UTXBRK.
To send a break character, the UTXBRK bit must be
set by software and must remain set for a minimum of
13 baud clock cycles. The UTXBRK bit is then cleared
by software to generate Stop bits. The user must wait
for a duration of at least one or two baud clock cycles
in order to ensure a valid Stop bit(s) before reloading
the UxTXB or starting other transmitter activity.
Transmission of a break character does not generate a
transmit interrupt.
18.4
Receiving Data
18.4.1
RECEIVING IN 8-BIT OR 9-BIT DATA
MODE
The following steps must be performed while receiving
8-bit or 9-bit data:
1.
Set up the UART (see Section 18.3.1
2.
Enable
the
UART
(see
3.
A receive interrupt will be generated when one
or more data words have been received,
depending on the receive interrupt settings
specified by the URXISEL bits (UxSTA<7:6>).
4.
Read the OERR bit to determine if an overrun
error has occurred. The OERR bit must be reset
in software.
5.
Read the received data from UxRXREG. The act
of reading UxRXREG will move the next word to
the top of the receive FIFO, and the PERR and
FERR values will be updated.
18.4.2
RECEIVE BUFFER (UXRXB)
The receive buffer is 4 words deep. Including the
Receive Shift register (UxRSR), the user effectively
has a 5-word deep FIFO buffer.
URXDA (UxSTA<0>) = 1 indicates that the receive
buffer has data available. URXDA = 0 implies that the
buffer is empty. If a user attempts to read an empty
buffer, the old values in the buffer will be read and no
data shift will occur within the FIFO.
The FIFO is reset during any device Reset. It is not
affected when the device enters or wakes up from a
Power-Saving mode.
18.4.3
RECEIVE INTERRUPT
The receive interrupt flag (U1RXIF or U2RXIF) can be
read from the corresponding Interrupt Flag register.
The interrupt flag is set by an edge generated by the
receiver. The condition for setting the receive interrupt
flag depends on the settings specified by the
URXISEL<1:0> (UxSTA<7:6>) control bits.
a) If URXISEL<1:0> = 00 or 01, an interrupt is
generated every time a data word is transferred
from the Receive Shift register (UxRSR) to the
Receive Buffer. There may be one or more
characters in the receive buffer.
b) If URXISEL<1:0> = 10, an interrupt is generated
when a word is transferred from the Receive
Shift register (UxRSR) to the Receive Buffer,
which, as a result of the transfer, contains
3 characters.
c)
If URXISEL<1:0> = 11, an interrupt is set when
a word is transferred from the Receive Shift reg-
ister (UxRSR) to the Receive Buffer, which, as a
result of the transfer, contains 4 characters (i.e.,
becomes full).
Switching between the Interrupt modes during opera-
tion is possible, though generally not advisable during
normal operation.
18.5
Reception Error Handling
18.5.1
RECEIVE BUFFER OVERRUN
ERROR (OERR BIT)
The OERR bit (UxSTA<1>) is set if all of the following
conditions occur:
a) The receive buffer is full.
b) The Receive Shift register is full, but unable to
transfer the character to the receive buffer.
c)
The Stop bit of the character in the UxRSR is
detected, indicating that the UxRSR needs to
transfer the character to the buffer.
Once OERR is set, no further data is shifted in UxRSR
(until the OERR bit is cleared in software or a Reset
occurs). The data held in UxRSR and UxRXREG
remains valid.
相關PDF資料
PDF描述
DSPIC30F6010-20E/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6010A-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-30I/PF IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6014-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC33EP512MU814-I/PL IC DSC 16BIT 512KB 144LQFP
相關代理商/技術參數
參數描述
dsPIC30F5015T-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F5015T-20I/PT 功能描述:IC DSPIC MCU/DSP 66K 64TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
dsPIC30F5015T-30I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F5016-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F5016-20I/PT 功能描述:IC DSPIC MCU/DSP 66K 80TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*