- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPB56007FJ66 DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC PDF資料下載
參數資料
| 型號： | DSPB56007FJ66 |
| 英文描述： | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| 中文描述： | 數字信號處理器| 24位|的CMOS | QFP封裝| 80腳|塑料 |
| 文件頁數： | 23/83頁 |
| 文件大?。?/td> | 382K |
| 代理商： | DSPB56007FJ66 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
Signal/Connection Descriptions
On-Chip Emulation (OnCE
TM
) Port
MOTOROLA
DSP56007/D
1-17
DSCK
OS1
Input
Output
Output,
Driven Low
Debug Serial Clock (DSCK)
—The DSCK/ OS1 signal,
when an input, is the signal through which the serial clock
is supplied to the OnCE port. The serial clock provides
pulses required to shift data into and out of the OnCE port.
Data is clocked into the OnCE port on the falling edge and
is clocked out of the OnCE port on the rising edge.
Operating Status 1 (OS1)
—If the OS1 signal is an output
and used in conjunction with the OS0 signal, it provides
information about the DSP status when the DSP is not in the
Debug mode. The debug serial clock frequency must be no
greater than 1/ 8 of the processor clock frequency. The
signal is tri-stated when it is changing from input to output.
Note:
If the OnCE port is in use, an external pull-down resistor
should be attached to the DSCK/ OS1 pin. If the OnCE
port is not in use, the resistor is not required.
DSO
Output
Driven High
Debug Serial Output (DSO)
—The DSO line provides the
data contained in one of the OnCE port controller registers
as specified by the last command received from the
command controller. The Most Significant Bit (MSB) of the
data word is always shifted out of the OnCE port first. Data
is clocked out of the OnCE port on the rising edge of DSCK.
The DSO line also provides acknowledge pulses to the
external command controller. When the DSP enters the
Debug mode, the DSO line will be pulsed low to indicate
that the OnCE port is waiting for commands. After
receiving a read command, the DSO line will be pulsed low
to indicate that the requested data is available and the
OnCE port is ready to receive clock pulses in order to
deliver the data. After receiving a write command, the DSO
line will be pulsed low to indicate that the OnCE port is
ready to receive the data to be written; after the data is
written, another acknowledge pulse will be provided.
Note:
During hardware reset and when idle, the DSO line is
held high.
Table 1-12
On-Chip Emulation Port Signals (Continued)
Signal
Name
Signal
Type
State during
Reset
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| DSPB56007FJ88 | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| DSPE56007FJ50 | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| DSPE56007FJ66 | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| DSPE56007FJ88 | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| DSPCOMMANDUM | Universal Command Converter for DSP User＇s Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPB56007FJ88 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| DSPB56011 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:24-BIT DVD DIGITAL SIGNAL PROCESSOR |
| DSPB56362AG120 | 功能描述:數字信號處理器和控制器 - DSP, DSC LEAD FREE DSP56362 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPB56362AG120 | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor |
| DSPB56362PV100 | 制造商:Rochester Electronics LLC 功能描述:DIGITAL AUDIO DSP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。