- 您現在的位置：買賣IC網 > PDF目錄385274 > DS33Z11 (MAXIM INTEGRATED PRODUCTS INC) Ethernet Mapper PDF資料下載
參數資料
| 型號： | DS33Z11 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 網絡接口 |
| 英文描述： | Ethernet Mapper |
| 中文描述： | DATACOM, NETWORK INTERFACE SUPPORT CIRCUIT, PBGA169 |
| 封裝： | 14 X 14 MM, 1 MM PITCH, CSBGA-169 |
| 文件頁數： | 81/169頁 |
| 文件大?。?/td> | 1049K |
| 代理商： | DS33Z11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁
DS33Z11 Ethernet Mapper
81 of 169
9.4 BERT Registers
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 7: This bit must be kept low for proper operation.
BCR
BERT Control Register
80h
7
-
0
6
5
4
3
2
1
0
PMU
0
RNPL
0
RPIC
0
MPR
0
APRD
0
TNPL
0
TPIC
0
Bit 6: Performance Monitoring Update (PMU)
This bit causes a performance monitoring update to be initiated.
A 0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the
counters reset (0 or 1). For a second performance monitoring update to be initiated, this bit must be set to 0, and
back to 1. If PMU goes low before the PMS bit goes high, an update might not be performed.
Bit 5: Receive New Pattern Load (RNPL)
A zero to one transition of this bit will cause the programmed test
pattern (QRSS, PTS, PLF [4:0}, PTF [4:0], and BSP [31:0]) to be loaded in to the receive pattern generator. This
bit must be changed to zero and back to one for another pattern to be loaded. Loading a new pattern will forces
the receive pattern generator out of the “Sync” state which causes a resynchronization to be initiated. Note: QRSS,
PTS, PLF [4:0}, PTF [4:0], and BSP [31:0] must not change from the time this bit transitions from 0 to 1 until four
RCLKI clock cycles after this bit transitions from 0 to 1.
Bit 4: Receive Pattern Inversion Control (RPIC)
When 0, the receive incoming data stream is not altered. When
1, the receive incoming data stream is inverted.
Bit 3: Manual Pattern Resynchronization (MPR)
A zero to one transition of this bit will cause the receive pattern
generator to resynchronize to the incoming pattern. This bit must be changed to zero and back to one for another
resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the
“Sync” state.
Bit 2: Automatic Pattern Resynchronization Disable (APRD)
When 0, the receive pattern generator will
automatically resynchronize to the incoming pattern if six or more times during the current 64-bit window the
incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern
generator will not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is
prevented by not allowing the receive pattern generator to automatically exit the “Sync” state.
Bit 1: Transmit New Pattern Load (TNPL)
A zero to one transition of this bit will cause the programmed test
pattern (QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit
must be changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0}, PTF[4:0],
and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TCLKI clock cycles after this
bit transitions from 0 to 1.
Bit 0: Transmit Pattern Inversion Control (TPIC)
When 0, the transmit outgoing data stream is not altered.
When 1, the transmit outgoing data stream is inverted.
相關PDF資料 |
PDF描述 |
|---|---|
| DS33ZH11 | Ethernet Mapper |
| DS3803 | 1024K Flexible NV SRAM SIMM(1024K靈活的非易失性SRAM SIMM) |
| DS3903E-020 | Triple 128-Position Nonvolatile Digital Potentiometer |
| DS3994 | 4-Channel Cold-Cathode Fluorescent Lamp Controller |
| DS4077 | 77.76MHz VCXO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS33Z11+ | 功能描述:網絡控制器與處理器 IC Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z11+UNUSED | 功能描述:網絡控制器與處理器 IC Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z11DK | 功能描述:以太網開發工具 DS33Z11 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| DS33Z41 | 功能描述:網絡控制器與處理器 IC Quad IMUX Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z41DK | 功能描述:以太網開發工具 DS33Z41 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。