參數資料
型號： DS2196LN+
廠商： Maxim Integrated Products
文件頁數： 25/157頁
文件大?。?/td> 0K
描述： IC FRAMER DUAL T1 LIU 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
控制器類型： T1 調幀器
接口： 并行/串行
電源電壓： 3.135 V ~ 3.465 V
電流 - 電源： 85mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
DS2196
120 of 157
Table 19-2: TRANSFORMER SPECIFICATIONS
SPECIFICATION
RECOMMENDED VALUE
Turns Ratio
1:1(receive) and 1:2(transmit) 5%
Primary Inductance
600
mH minimum
Leakage Inductance
1.0
mH maximum
Intertwining Capacitance
40 pF maximum
Transmit Transformer DC Resistance
Primary (Device side)
Secondary
1.0
W maximum
2.0
W maximum
Receive Transformer DC Resistance
Primary (Device side)
Secondary
1.2
W maximum
1.2
W maximum
19.3JITTER ATTENUATOR
The DS2196 contains an onboard jitter attenuator that can be set to a depth of either 32 or 128 bits via the
JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications
where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.
The characteristics of the attenuation are shown in Figure 19–4. The jitter attenuator can be placed in
either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.
Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR. In
order for the jitter attenuator to operate properly, a 1.544 MHz clock (50 ppm) must be applied at the
MCLK pin. Onboard circuitry adjusts either the recovered clock from the clock/data recovery block or
the clock applied at the TCLKLI pin to create a smooth jitter free clock which is used to clock data out of
the jitter attenuator FIFO. It is acceptable to provide a gapped/ bursty clock at the TCLKLI pin if the
jitter attenuator is placed on the transmit side. If the incoming jitter exceeds either 120 UIpp (buffer
depth is 128 bits) or 28 UIpp (buffer depth is 32 bits), then the DS2196 will divide the internal nominal
24.704 MHz clock by either 15 or 17 instead of the normal 16 to keep the buffer from overflowing.
When the device divides by either 15 or 17, it also sets the Jitter Attenuator Limit Trip (JALT) bit in the
Receive Information Register (RIR3.5)
相關PDF資料
PDF描述
DS21FF42 IC FRAMER T1 4X4 16CH 300-BGA
DS21FF44 IC FRAMER E1 4X4 16CH 300-BGA
DS21FT44N+ IC FRAMER 4X4 16CH 300-BGA
DS21Q352B IC TXRX QUAD T1/E1 3.3V 256-BGA
DS21Q41BT IC FRAMER T1 QUAD 128-TQFP
相關代理商/技術參數
參數描述
DS2196LN+ 功能描述:網絡控制器與處理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS219T 功能描述:烙鐵 DESOLDERING HEAD RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
DS21E352 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E352N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E354 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*