- 您現在的位置：買賣IC網 > PDF目錄380227 > CYWUSB6934-48LFXC (CYPRESS SEMICONDUCTOR CORP) Multiconductor Cable; Number of Conductors:2; Conductor Size AWG:18; No. Strands x Strand Size:7 x 26; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Capacitance:30pF/ft; Conductor Material:Copper RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | CYWUSB6934-48LFXC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Multiconductor Cable; Number of Conductors:2; Conductor Size AWG:18; No. Strands x Strand Size:7 x 26; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Capacitance:30pF/ft; Conductor Material:Copper RoHS Compliant: Yes |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, QCC48 |
| 封裝： | 7 X 7 MM, LEAD FREE, MO-220, QFN-48 |
| 文件頁數： | 3/30頁 |
| 文件大?。?/td> | 305K |
| 代理商： | CYWUSB6934-48LFXC |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
CYWUSB6932
CYWUSB6934
Document 38-16007 Rev. *G
Page 3 of 30
4.5
Both ICs have a fully synchronous SPI slave interface for
connectivity to the application MCU. Configuration and
byte-oriented data transfer can be performed over this
interface. An interrupt is provided to trigger real time events.
An optional SERDES Bypass mode (DIO) is provided for appli-
cations that require a synchronous serial bit-oriented data
path. This interface is for data only.
Application Interfaces
4.6
A 13-MHz crystal (
±
50 ppm or better) is directly connected to
X13IN and X13 without the need for external capacitors. Both
ICs have a programmable trim capability for adjusting the
on-chip load capacitance supplied to the crystal. The Radio
Frequency (RF) circuitry has on-chip decoupling capacitors.
Both devices are powered from a 2.7V to 3.6V DC supply. Both
devices can be shutdown to a fully static state using the PD
pin.
Below are the requirements for the crystal to be directly
connected to X13IN and X13:
Nominal Frequency: 13 MHz
Operating Mode: Fundamental Mode
Resonance Mode: Parallel Resonant
Frequency Stability:
±
50 ppm
Series Resistance:
≤
100 ohms
Load Capacitance: 10 pF
Drive Level: 10 uW–100 uW
Clocking and Power Management
4.7
The RSSI register (Reg 0x22) (applies only to the
CYWUSB6934 IC) returns the relative signal strength of the
ON-channel signal power and can be used to:
1. Determine the connection quality
2. Determine the value of the noise floor
3. Check for a quiet channel before transmitting.
The internal RSSI voltage is sampled through a 5-bit
analog-to-digital converter (ADC). A state machine controls
the conversion process. Under normal conditions, the RSSI
state machine initiates a conversion when an ON-channel
carrier is detected and remains above the noise floor for over
50uS. The conversion produces a 5-bit value in the RSSI
register (Reg 0x22, bits 4:0) along with a valid bit, RSSI
register (Reg 0x22, bit 5). The state machine then remains in
HALT mode and does not reset for a new conversion until the
receive mode is toggled off and on. Once a connection has
been established, the RSSI register can be read to determine
the relative connection quality of the channel. A RSSI register
value lower than 10 indicates that the received signal strength
is low, a value greater than 28 indicates a strong signal level.
To check for a quiet channel before transmitting, first set up
receive mode properly and read the RSSI register (Reg 0x22).
If the valid bit is zero, then force the Carrier Detect register
Receive Signal Strength Indicator (RSSI)
(Reg 0x2F, bit 7=1) to initiate an ADC conversion. Then, wait
greater than 50uS and read the RSSI register again. Next,
clear the Carrier Detect Register (Reg 0x2F, bit 7=0) and turn
the receiver OFF. Measuring the noise floor of a quiet channel
is inherently a 'noisy' process so, for best results, this
procedure should be repeated several times (~20) to compute
an average noise floor level. A RSSI register value of 0-10
indicates a channel that is relatively quiet. A RSSI register
value greater than 10 indicates the channel is probably being
used. A RSSI register value greater than 28 indicates the
presence of a strong signal.
5.0
Application Interfaces
5.1
The CYWUSB6932/CYWUSB6934 ICs have a four-wire SPI
communication interface between an application MCU and
one or more slave devices. The SPI interface supports
single-byte and multi-byte serial transfers. The four-wire SPI
communications interface consists of Master Out-Slave In
(MOSI), Master In-Slave Out (MISO), Serial Clock (SCK), and
Slave Select (SS).
The SPI receives SCK from an application MCU on the SCK
pin. Data from the application MCU is shifted in on the MOSI
pin. Data to the application MCU is shifted out on the MISO
pin. The active-low Slave Select (SS) pin must be asserted to
initiate a SPI transfer.
The application MCU can initiate a SPI data transfer via a
multi-byte transaction. The first byte is the Command/Address
byte, and the following bytes are the data bytes as shown in
Figure 5-1
through
Figure 5-4
. The SS signal should not be
deasserted between bytes. The SPI communications is as
follows:
Command Direction (bit 7) = “0” Enables SPI read transac-
tion. A “1” enables SPI write transactions.
Command Increment (bit 6) = “1” Enables SPI auto address
increment. When set, the address field automatically incre-
ments at the end of each data byte in a burst access, oth-
erwise the same address is accessed.
Six bits of address.
Eight bits of data.
The SPI communications interface has a burst mechanism,
where the command byte can be followed by as many data
bytes as desired. A burst transaction is terminated by
deasserting the slave select (SS = 1). For burst read transac-
tions, the application MCU must abide by the timing shown in
Figure 12-2
.
The SPI communications interface single read and burst read
sequences are shown in
Figure 5-2
and
Figure 5-3
, respec-
tively.
The SPI communications interface single write and burst write
sequences are shown in
Figure 5-4
and
Figure 5-5
, respec-
tively.
SPI Interface
相關PDF資料 |
PDF描述 |
|---|---|
| CYWUSB6935-48LFXC | WirelessUSB LRTM 2.4-GHz DSSS Radio SoC |
| CYWUSB6935-48LFXI | WirelessUSB LRTM 2.4-GHz DSSS Radio SoC |
| CYWUSB6941 | WirelessUSB EX Radio |
| CYWUSB6941-42BAC | WirelessUSB EX Radio |
| CYWUSB6942 | WirelessUSB EX Radio |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYWUSB6934-48LTXC | 功能描述:射頻收發器 2.4 GHz Wireless USB RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| CYWUSB6935 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:WirelessUSB LRTM 2.4-GHz DSSS Radio SoC |
| CYWUSB6935_10 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:WirelessUSBa?￠ LR 2.4 GHz DSSS Radio SoC |
| CYWUSB6935-28SEI | 功能描述:IC WIRELESS USB 2.4GHZ 28-SOIC RoHS:否 類別:RF/IF 和 RFID >> RF 收發器 系列:WirelessUSB™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
| CYWUSB6935-48LFI | 功能描述:IC USB WIRELESS 2.4GHZ 48VQFN RoHS:否 類別:RF/IF 和 RFID >> RF 收發器 系列:WirelessUSB™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。