- 您現在的位置：買賣IC網 > PDF目錄380227 > CYV15G0404DXB-BGI (CYPRESS SEMICONDUCTOR CORP) Independent Clock Quad HOTLink II⑩ Transceiver with Reclocker PDF資料下載
參數資料
| 型號： | CYV15G0404DXB-BGI |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Independent Clock Quad HOTLink II⑩ Transceiver with Reclocker |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | 27 X 27 MM, 1.57 MM HEIGHT, TBGA-256 |
| 文件頁數： | 12/43頁 |
| 文件大?。?/td> | 814K |
| 代理商： | CYV15G0404DXB-BGI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
PRELIMINARY
CYV15G0404DXB
Document #: 38-02097 Rev. **
Page 12 of 43
CYV15G0404DXB HOTLink II Operation
The CYV15G0404DXB is a highly configurable, independent
clocking, quad-channel transceiver designed to support
reliable transfer of large quantities of data, using high-speed
serial links from multiple sources to multiple destinations. This
device supports four single-byte channels.
CYV15G0404DXB Transmit Data Path
Input Register
The bits in the Input Register for each channel support
different assignments, based on if the input data is encoded or
unencoded. These assignments are shown in
Table 1
.
When the ENCODER is enabled, each input register captures
eight data bits and two control bits on each input clock cycle.
When the Encoder is bypassed, the control bits are part of the
pre-encoded 10-bit character.
When the Encoder is enabled, the TXCTx[1:0] bits are inter-
preted along with the associated TXDx[7:0] character to
generate a specific 10-bit transmission character.
Phase-Align Buffer
Data from each Input Register is passed to the associated
Phase-Align Buffer, when the TXDx[7:0] and TXCTx[1:0] input
registers are clocked using TXCLKx| (TXCKSELx = 0 and
TXRATEx = 0). When the TXDx[7:0] and TXCTx[1:0] input
registers are clocked using REFCLKx± (TXCKSELx = 1) and
REFCLKx± is a full-rate clock, the associated Phase
Alignment Buffer in the transmit path is bypassed. These
buffers are used to absorb clock phase differences between
the TXCLKx input clock and the internal character clock for
that channel.
SCANEN2
LVTTL input,
internal pull-down
LVTTL input,
internal pull-down
Factory Test 2.
SCANEN2 input is for factory testing only. This input may be left
as a NO CONNECT, or GND only.
Factory Test 3
. TMEN3 input is for factory testing only. This input may be left as
a NO CONNECT, or GND only.
TMEN3
Analog I/O
OUTA1±
OUTB1±
OUTC1±
OUTD1±
OUTA2±
OUTB2±
OUTC2±
OUTD2±
INA1±
INB1±
INC1±
IND1±
INA2±
INB2±
INC2±
IND2±
JTAG Interface
TMS
CML Differential
Output
Primary Differential Serial Data Output
. The OUTx1± PECL-compatible CML
outputs (+3.3V referenced) are capable of driving terminated transmission lines
or standard fiber-optic transmitter modules, and must be AC-coupled for PECL-
compatible connections.
Secondary Differential Serial Data Output
. The OUTx2± PECL-compatible CML
outputs (+3.3V referenced) are capable of driving terminated transmission lines or
standard fiber-optic transmitter modules, and must be AC-coupled for PECL-compatible
connections.
Primary Differential Serial Data Input
. The INx1± input accepts the serial data
stream for deserialization and decoding. The INx1± serial stream is passed to the
receive CDR circuit to extract the data content when INSELx = HIGH.
CML Differential
Output
Differential Input
Differential Input
Secondary Differential Serial Data Input
. The INx2± input accepts the serial
data stream for deserialization and decoding. The INx2± serial stream is passed
to the receiver CDR circuit to extract the data content when INSELx = LOW.
LVTTL Input,
internal pull-up
LVTTL Input,
internal pull-down
3-State LVTTL Output
Test Data Out
. JTAG data output buffer. High-Z while JTAG test mode is not
selected.
LVTTL Input,
internal pull-up
LVTTL Input,
internal pull-up
JTAG test access port controller.
Test Mode Select
. Used to control access to the JTAG Test Modes. If maintained
high for
≥
5 TCLK cycles, the JTAG test controller is reset.
JTAG Test Clock
.
TCLK
TDO
TDI
Test Data In
. JTAG data input port.
TRST
JTAG reset signal
. When asserted (LOW), this input asynchronously resets the
Power
V
CC
GND
+3.3V Power
.
Signal and Power Ground for all internal circuits
.
Pin Definitions
(continued)
CYV15G0404DXB Quad HOTLink II Transceiver
Name
I/O Characteristics
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| CYW15G0201DXB | Dual-channel HOTLink II Transceiver(雙通道HOTLink II收發器) |
| CYW15G0401DXB | Quad HOTLink II Transceiver(四熱連接II收發器) |
| CYW2330 | Dual Serial Input PLL with 2.5-GHz and 600-MHz Prescalers |
| CYW2331 | Dual Serial Input PLL with 2.0-GHz and 600-MHz Prescalers |
| CYW2336 | Dual Serial Input PLL with 2.0- and 1.1-GHz Prescalers(帶2.0-GHz 預標定器的串聯輸入PLL) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYV15G0404DXB-BGXC | 功能描述:電信線路管理 IC 3.3V QUAD HOTLINK II TRANS W/RECLOCKER RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYV15G0404DX-EVAL | 功能描述:界面開發工具 Quad Indep Ch HOTLink II XCVR RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CYV15G0404RB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II⑩ Deserializing Reclocker |
| CYV15G0404RB_07 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II⑩ Deserializing Reclocker |
| CYV15G0404RB-BGC | 功能描述:電信線路管理 IC 4x Indep Reclockers COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。