- 您現在的位置：買賣IC網 > PDF目錄380161 > CY4615 (Cypress Semiconductor Corp.) EZ-USB AT2⑩ USB 2.0 to ATA/ATAPI Bridge PDF資料下載
參數資料
| 型號： | CY4615 |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | EZ-USB AT2⑩ USB 2.0 to ATA/ATAPI Bridge |
| 中文描述： | 的EZ - USB AT2⑩個USB 2.0到ATA / ATAPI的橋 |
| 文件頁數： | 24/26頁 |
| 文件大?。?/td> | 193K |
| 代理商： | CY4615 |
CY7C68300
Document #: 38-08011 Rev. *B
Page 24 of 26
12.0
The following recommendations should be followed to ensure reliable high-performance operation.
At least a four-layer impedance controlled boards are required to maintain signal quality.
Specify impedance targets (ask your board vendor what they can achieve).
To control impedance, maintain trace widths and trace spacing.
Minimize stubs to minimize reflected signals.
Connections between the USB connector shell and signal ground must be done near the USB connector.
Bypass/flyback caps on VBus, near connector, are recommended.
DPLUS and DMINUS trace lengths should be kept to within 2 mm of each other in length, with preferred length of 20-30mm.
Maintain a solid ground plane under the DPLUS and DMINUS traces. Do not allow the plane to be split under these traces.
It is preferred is to have no vias placed on the DPLUS or DMINUS trace routing.
Isolate the DPLUS and DMINUS traces from all other signal traces by no less than 10 mm.
Source for recommendations:
EZ-USB FX2
PCB Design Recommendations, http:///www.cypress.com/cfuploads/support/app_notes/FX2_PCB.pdf.
High-speed USB Platform Design Guidelines, http://www.usb.org/developers/data/hs_usb_pdg_r1_0.pdf.
PCB Layout Recommendations
13.0
Quad Flat Package No Leads (QFN) Package Design Notes
Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the bottom surface of the
package to the PCB. Hence, special attention is required to the heat transfer area below the package to provide a good thermal
bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transferred
from the AT2 through the device
’
s metal paddle on the bottom side of the package. Heat from here is conducted to the PCB at
the thermal pad. It is then conducted from the thermal pad to the PCB inner ground plane by a 5 x 5 array of Via. A Via is a plated
through-hole in the PCB with a finished diameter of 13 mil. The QFN
’
s metal die paddle must be soldered to the PCB
’
s thermal
pad. Solder mask is placed on the board top side over each Via to resist solder flow into the Via. The mask on the top side also
minimizes outgassing during the solder reflow process.
For further information on this package design please refer to the application note
“
Surface Mount Assembly of AMKOR
’
s
MicroLeadFrame (MLF) Technology.
”
This application note can be downloaded from AMKOR
’
s website from the following URL
http://www.amkor.com/products/notes_papers/MLF_AppNote_0301.pdf. The application note provides detailed information on
board mounting guidelines, soldering flow, rework process, etc.
Figure 13-1
below display a cross-sectional area underneath the package. The cross section is of only one via. The solder paste
template needs to be designed to allow at least 50% solder coverage. The thickness of the solder paste template should be 5 mil.
It is recommended that
“
No Clean
”
, type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during
reflow.
Figure 13-2
is a plot of the solder mask pattern and
Figure 13-3
displays an X-Ray image of the assembly (darker areas indicate
solder.)
Figure 13-1. Cross-Section of the Area Underneath the QFN Package
0.017
”
dia
Solder Mask
Cu Fill
Cu Fill
PCB Material
PCB Material
0.013
”
dia
Via hole for thermally connecting the
QFN to the circuit board ground plane.
This figure only shows the top three layers of the
circuit board: Top Solder, PCB Dielectric, and
the Ground Plane
相關PDF資料 |
PDF描述 |
|---|---|
| CY53120 | Neuron Chip Network Processor(Neuron 芯片網絡處理器) |
| CY53150 | Neuron Chip Network Processor(Neuron 芯片網絡處理器) |
| CY5474FCT138T | 1-of-8 Decoder |
| CY54FCT163TLCC | 4-Bit Binary Counter |
| CY54FCT163TQSOP | 4-Bit Binary Counter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY4615A | 功能描述:開發板和工具包 - 其他處理器 Development Board COM RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| CY4615B | 功能描述:界面開發工具 Reference Design Kit COM RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CY4616 | 制造商:Cypress Semiconductor 功能描述:HIGH SPEED USB TO ATA - Bulk |
| CY4617 | 功能描述:開發板和工具包 - 其他處理器 Development Board COM RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| CY4617-CF | 制造商:Cypress Semiconductor 功能描述:USB LS DEVELOPMENT KIT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。