- 您現在的位置：買賣IC網 > PDF目錄380161 > CY4615 (Cypress Semiconductor Corp.) EZ-USB AT2⑩ USB 2.0 to ATA/ATAPI Bridge PDF資料下載
參數資料
| 型號： | CY4615 |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | EZ-USB AT2⑩ USB 2.0 to ATA/ATAPI Bridge |
| 中文描述： | 的EZ - USB AT2⑩個USB 2.0到ATA / ATAPI的橋 |
| 文件頁數： | 11/26頁 |
| 文件大小： | 193K |
| 代理商： | CY4615 |
CY7C68300
Document #: 38-08011 Rev. *B
Page 11 of 26
4.0
Functional Overview
4.1
EZ-USB AT2 operates at two of the three rates defined in the USB Specification Revision 2.0 dated April 27, 2000:
Full speed, with a signaling bit rate of 12 Mbits/sec
High speed, with a signaling bit rate of 480 Mbits/sec.
EZ-USB AT2 does not support the low-speed signaling rate of 1.5 Mbits/sec.
USB Signaling Speed
4.2
The ATA/ATAPI port on the EZ-USB AT2 is compliant with the Information Technology AT Attachment with Packet Interface 6
(ATA/ATAPI-6) Specification, T13/1410D Rev 3B. The EZ-USB AT2 supports both ATAPI packet commands over USB.
Additionally, the EZ-USB AT2 translates ATAPI SFF-8070i commands to ATA commands for seamless integration of ATA devices
with generic Mass Storage Class BOT drivers.
ATA Interface
5.0
During the power-up sequence, internal logic checks the I
2
C-compatible port for an EEPROM whose first two bytes are both
0x4D. If a valid signature is found, the EZ-USB AT2 uses the values stored in the EEPROM to configure the USB descriptors for
normal operation. If an invalid EEPROM signature is read, or if no EEPROM is detected, the EZ-USB AT2 defaults into Board
Manufacturing Test Mode. The two modes of operation are described in subsections 5.1 and 5.2, below.
Enumeration
5.1
In Board Manufacturing Test Mode, the chip behaves as a USB 2.0 device but the ATA/ATAPI interface is not active. The EZ-USB
AT2 allows for reading and writing an EEPROM and for board level testing through vendor specific ATAPI commands utilizing the
CBW Command Block as described in the USB
Mass Storage Class Bulk-Only Transport Specification
. There is a vendor-specific
ATAPI command for the EEPROM access (CfgCB) and one for the board level testing (MfgCB).
Board Manufacturing Test Mode
5.1.1
The cfg_load and cfg_read vendor-specific commands are passed down through the bulk pipe in the CBWCB portion of the CBW.
The format of this CfgCB is shown below. Byte 0 will be a vendor-specific command designator whose value is configurable and
set in the configuration data (EEPROM address 0x04). Byte 1 must be set to 0x26 to identify CfgCB. Byte 2 is reserved and must
be set to zero. Byte 3 is used to determine the memory source to write/read. For the EZ-USB AT2, this byte must be set to 0x02,
meaning the EEPROM. Bytes 4 and 5 will be used to determine the start address. For the EZ-USB AT2, this must always be
0x0000. Bytes 6 through 15 are reserved and should be set to zero.
The data transferred to the EEPROM must be in the format specified in
Table 5-6
of this data sheet. Maximum data transfer size
is 255 bytes.
The data transfer length is determined by the CBW Data Transfer Length specified in bytes 8 through 11 (dCBWDataTransfer-
Length) of the CBW. The type/direction of the command will be determined by the direction bit specified in byte 12, bit 7 (bmCBW-
Flags) of the CBW.
Table 5-1. Command Block Wrapper
CfgCB
7
6
5
4
3
2
1
0
0
–
3
4
–
7
8
–
11 (08h-0Bh)
12 (0Ch)
DCBWSignature
dCBWTag
dCBWDataTransferLength
bwCBWFLAGS
Dir
Obsolete
Reserved (0)
Reserved (0)
Reserved (0)
13 (0Dh)
14 (0Eh)
15-30 (0Fh1Eh)
Table 5-2. Example CfgCB
bCBWLUN
bCBWCBLength
CBWCB (CfgCB or MfgCB)
CfgCB Byte Descriptions
Bits
7
0
6
0
5
1
4
0
3
0
2
1
1
0
0
0
0 bVSCBSignature (set in configuration bytes)
相關PDF資料 |
PDF描述 |
|---|---|
| CY53120 | Neuron Chip Network Processor(Neuron 芯片網絡處理器) |
| CY53150 | Neuron Chip Network Processor(Neuron 芯片網絡處理器) |
| CY5474FCT138T | 1-of-8 Decoder |
| CY54FCT163TLCC | 4-Bit Binary Counter |
| CY54FCT163TQSOP | 4-Bit Binary Counter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY4615A | 功能描述:開發板和工具包 - 其他處理器 Development Board COM RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| CY4615B | 功能描述:界面開發工具 Reference Design Kit COM RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CY4616 | 制造商:Cypress Semiconductor 功能描述:HIGH SPEED USB TO ATA - Bulk |
| CY4617 | 功能描述:開發板和工具包 - 其他處理器 Development Board COM RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| CY4617-CF | 制造商:Cypress Semiconductor 功能描述:USB LS DEVELOPMENT KIT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。