參數資料
型號: AT85C51SND3B1-7FTUL
廠商: Atmel
文件頁數: 7/119頁
文件大?。?/td> 0K
描述: IC DECODER/ENCODER DGTL 100CBGA
標準包裝: 90
類型: 音頻編碼器/解碼器
應用: 移動電話,手機,視頻顯示器
電壓 - 電源,數字: 1.65 V ~ 3.6 V
安裝類型: 表面貼裝
封裝/外殼: 100-TFBGA
供應商設備封裝: 100-CTBGA(9x9)
包裝: 托盤
104
AT85C51SND3B
7632D–MP3–01/07
the host sends a SETUP command (SET_ADDRESS(addr)),
the firmware records that address in UADD, but keep ADDEN cleared,
the USB device sends an IN command of 0 bytes (IN 0 Zero Length Packet),
then, the firmware can enable the USB device address by setting ADDEN. The only
accepted address by the controller is the one stored in UADD.
ADDEN and UADD shall not be written at the same time.
UADD contains the default address 00h after a power-up or USB reset.
ADDEN is cleared by hardware:
after a power-up reset,
when an USB reset is received,
or when the macro is disabled (USBE cleared)
When this bit is cleared, the default device address 00h is used.
Suspend, Wake-Up and
Resume
After a period of 3 ms during which the USB line was inactive, the controller switches to
the full-speed mode and triggers (if enabled) the SUSPI (suspend) interrupt. The firm-
ware may then set the FRZCLK bit.
The CPU can also, depending on software architecture, enter in the idle mode to lower
again the power consumption.
There are two ways to recover from the “Suspend” mode:
First one is to clear the FRZCLK bit. This is possible if the CPU is not in the Idle
mode.
Second way, if the CPU is “idle”, is to enable the WAKEUPI interrupt (WAKEUPE
set). Then, as soon as an non-idle signal is seen by the controller, the WAKEUPI
interrupt is triggered. The firmware shall then clear the FRZCLK bit to restart the
transfer.
There are no relationship between the SUSPI interrupt and the WAKEUPI interrupt: the
WAKEUPI interrupt is triggered as soon as there are non-idle patterns on the data lines.
Thus, the WAKEUPI interrupt can occurs even if the controller is not in the “suspend”
mode.
When the WAKEUPI interrupt is triggered, if the SUSPI interrupt bit was already set, it is
cleared by hardware.
When the SUSPI interrupt is triggered, if the WAKEUPI interrupt bit was already set, it is
cleared by hardware.
Detach
The reset value of the DETACH bit is 1.
It is possible to re-enumerate a device, simply by setting and clearing the DETACH bit.
If the USB device controller is in full-speed mode, setting DETACH will disconnect
the pull-up on the D+ or D- pad (depending on full or low speed mode selected).
Then, clearing DETACH will connect the pull-up on the D+ or D- pad.
相關PDF資料
PDF描述
JN1FS04FKK CONN PLUG 4POS R/A W/SOCKET SLD
AD1970JSTZRL IC ENCODER BTSC W/CODEC 48-LQFP
ADV7177KSZ IC DAC VIDEO NTSC 3-CH 44MQFP
VI-24L-CU-S CONVERTER MOD DC/DC 28V 200W
VI-24K-CU-S CONVERTER MOD DC/DC 40V 200W
相關代理商/技術參數
參數描述
AT85C51SND3B1N-DDV 功能描述:音頻 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
AT85C51SND3B1N-RTTUL 功能描述:音頻 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
AT85C51SND3B1-RTTUL 功能描述:音頻 DSP MP3/WMA USB2.0 w/o DAC+DC/DC RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
AT85C51SND3B2-RTTUL 功能描述:音頻 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
AT85C51SND3BX 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:MP3 Microcontrollers