參數資料
型號： AT43USB320A-AC
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： Full-speed USB Microcontroller with an Embedded Hub
中文描述： 8-BIT, 12 MHz, RISC MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, MS-026AED, LQFP-100
文件頁數： 95/115頁
文件大?。?/td> 722K
代理商： AT43USB320A-AC
95
AT43USB320A
1443E–USB–4/04
Bit 1 – PESC: Port Enable/Disable Status Change
0 = No change has occurred on Port Enable/Disable Status
1 = Port Enable/Disable status has changed
Set by hardware due to babble, physical disconnect or overcurrent except for Port 5 in which
case it is set by hardware at EOF2 due to hardware events. Cleared by firmware via Host
request ClearPortFeature(PORT_ENABLE).
Bit 0 – PCSC: Port Connect Status Change
0 = No change has occurred on Current Connect Status
1 = Current Connect Status has changed
This bit is set by hardware at EOF2 after it detects a connect or disconnect at a port, except for
Port 5. Hardware sets this bit for Port 5 after a hub reset. Cleared by firmware via Host request
ClearPortFeature(PORT_CONNECTION).
Hub and Port Power
Management
For the utmost flexibility, the USB hardware of the AT43USB320A is designed to accommo-
date hubs of various capacitance. Management of the downstream port power is also defined
by the firmware: per port or global overcurrent sensing, individual or gang power switching.
While the interface to the external power supply monitoring and switching is achieved through
the microcontroller’s GPIO pins, the USB hardware of the AT43USB320A contains the cir-
cuitry to handle all the possible combinations port power management tasks.
Overcurrent sensing
1.
Global Overcurrent Protection
– In this mode, the Port Overcurrent Indicator and
Port Overcurrent Indicator Change should be set to 0's. For the AT43USB320A an
external solid state switch, such as the Micrel MIC2545-2, is required to switch power
to the external USB ports. The FLG# output of the switch should be connected to PD0.
When an overcurrent occurs, FLG is asserted and the firmware should set the Hub
Overcurrent Indicator and Hub Overcurrent Indicator Change and switch off power to
the hub.
Individual Port Over-current Protection
– The Hub Overcurrent Indicator and Hub
Overcurrent Indicator Change bits should be set to 0's. One MIC2026-2 is required for
each two USB ports. Each of the FLG# outputs of the MIC2026-2 should be connected
to an unused microcontroller port. An overcurrent is indicated by assertion of FLG#.
The firmware sets the corresponding port's Overcurrent Indicator and the Overcurrent
Indicator Change bits and switches off power to the port. At the next IN token from the
Host, the AT43USB320A reports the status change.
2.
Port Power Switching
1.
Gang Power Switching
– One of the microcontroller I/O port pins must be pro-
grammed as an output to control the external switch, PWRN. Switch ON is requested
by the USB Host through the SetPortFeature(PORT_POWER) request. Switch OFF is
executed upon receipt of a ClearPortFeature(PORT_POWER) or upon detecting an
overcurrent condition. The firmware clears the Power Control Bit. Only if all of the
Power Control Bits of ports 1 through 4 are cleared should the firmware de-assert the
PWRN pin.
Individual Power Switching
– One microcontroller I/O port pin must be assigned for
each USB port to control the external switch, PWRxN, where x = 1, 2, 3, 4. Each of the
Power Control Bits controls one PWRxN.
Multiple Ganged Overcurrent Protection
– Overcurrent sensing is grouped physi-
cally into one or more gangs, but reported individually.
2.
3.
Figure 22 shows a simplified diagram of a power management circuit of an AT43USB320A
based hub design with global overcurrent protection and ganged power switching.
相關PDF資料
PDF描述
AT43USB321 Full-speed USB Hub/Function Microcontroller
AT43USB325E-AC Multimedia USB Keyboard Controller with Embedded Hub
AT43USB325E-AU Multimedia USB Keyboard Controller with Embedded Hub
AT43USB326-AC Multimedia USB Keyboard Controller with Embedded Hub
AT43USB326-AU Multimedia USB Keyboard Controller with Embedded Hub
相關代理商/技術參數
參數描述
AT43USB321 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed USB Hub/Function Microcontroller
AT43USB324AC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:KEYBOARD CONTROLLER
AT43USB324YC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:KEYBOARD CONTROLLER
AT43USB325 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Missed Watchdog Timer Reset
AT43USB325_05 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Multimedia USB Keyboard Controller with Embedded Hub
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*