參數資料
型號: AMIS-53000
英文描述: Frequency Agile Transceiver
中文描述: 捷變頻收發器
文件頁數: 7/99頁
文件大小: 2638K
代理商: AMIS-53000
AMIS-53000
Frequency Agile Transceiver
Data Sheet
1.4.2.5.
Manchester Data Encoding
The AMIS-53000 can encode the data as NRZ or Manchester.
1.4.2.6.
Oscillators
The AMIS-53000 requires a single external crystal working with the internal VCO and PLL to generate frequencies from 300MHz to
928MHz. The AMIS-53000 has internal capacitors that eliminate the need for external load capacitors when using a typical 24MHz
external crystal. The VCO requires an external inductor and capacitor (including internal capacitance) to produce the desired transmit
or receive RF frequency. The AMIS-53000 generates the desired RF transmit and receive frequencies from 300MHz to 928MHz by
selecting the proper inductor and capacitor value along with programming the frequency in the AMIS-53000. A patented Quick Start
circuit is used to force the crystal oscillator on to the desired frequency in microseconds rather than in milliseconds.
A low power internal 10kHz oscillator provides the timing for Sniff, Burst and housekeeping. The AMIS-53000 self-calibration circuits
can tune this oscillator to within two percent of 10kHz.
1.4.2.7.
Interface Serial Bus
The AMIS-53000 has separate interfaces for data and control. The transfer of TX/RX data between the AMIS-53000 and an external
host/controller is done with a 3-wire serial interface or a 4-wire SPI compatible serial interface. Control information is written to the
AMIS-53000 registers or read from the AMIS-53000 registers using either a 3-wire serial interface or a 2-wire I
2
C compatible serial
interface.
Once the AMIS-53000 configuration registers have data written to them for various operational modes such as, TX, RX, Sniff or other,
placing the AMIS-53000 into one of these modes is accomplished through a single write to the command register.
TX/RX Data Interface
The transmit or receive data interface of the AMIS-53000 can be programmed to be either a proprietary 3-wire serial interface or a
4-wire SPI compatible serial bus. The data interface can be set up to do either data transfers into a buffer in the AMIS-53000 or
streaming data (data is transmitted as it is received by the AMIS-53000 or data is sent to the host/controller as it is recovered in the
AMIS-53000 receiver). When using the buffered data mode, the AMIS-53000 can be the master or slave, but it must be the master to
do streaming data.
Control Interface
Once the AMIS-53000 is first powered on, an external host/controller sets the type of interface to the AMIS-53000 (3-wire or I
2
C) by
simply writing to the AMIS-53000 with the desire protocol. The AMIS-53000 will continue to use that interface protocol until power is
removed from the AMIS-53000. The AMIS-53000 is always a slave device for the control interface.
7
AMI Semiconductor
– Aug. 05, Rev. 1.0
www.amis.com
相關PDF資料
PDF描述
AMIS-53000-M Frequency Agile Transceiver
AMIS-53050 Frequency Agile Transceiver
AMIS-710650 Color CIS Module Analog Video Output
AMIS-710650-A6 Color CIS Module Analog Video Output
AMIS-710651 Color CIS Module
相關代理商/技術參數
參數描述
AMIS53000/19608-001XT 制造商:AMI Semiconductor 功能描述: 制造商:NTE Electronics 功能描述:
AMIS53000/SAMPLE 制造商:AMI Semiconductor 功能描述: 制造商:NTE Electronics 功能描述:
AMIS-53000-I/A 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver
AMIS-53000-M 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver
AMIS-53050 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Tape and Reel 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Tape and Reel