參數資料
型號： AMIS-53000
英文描述： Frequency Agile Transceiver
中文描述： 捷變頻收發器
文件頁數： 46/99頁
文件大?。?/td> 2638K
代理商： AMIS-53000
AMIS-53000
Frequency Agile Transceiver
Data Sheet
Setup registers descriptions:
Status
- Contains the results of calibrations, instructions and activity in the AMIS-53000.
Software State
- Shows the current mode of the AMIS-53000.
6.4.5.1.
Status/Flag1
The purpose of the Status1 register is to provide information back to the host on the status of the part. This register should be queried
at the completion of calibration sequences to ensure proper operation. The flags will be reset when the register is read.
CheckSum indicates whether an attempt to read or write the EE has failed due to an incorrect CheckSum.
Instruction enable indicates that the AMIS-53000 is ready to receive an instruction. This can be used to insure that the AMIS-53000
does not miss a command instruction due to the AMIS-53000 not being ready. Along with the busy flag, these status flags can police
the flow of commands to the AMIS-53000.
Table 29: Status/Flag1 - 0X01 [1]
Bit
Name
State
Comment
1
PLL out of lock on startup (RX, TX, Sniff, Burst)
7
PLL xLock
0
1
PLL calibration for transmit failed
6
TX PLL Cal
0
1
PLL calibration for receive failed
5
RX PLL Cal
0
1
10kHz RC oscillator calibration failed
4
RC Cal
0
1
Quick Start calibration failed
3
Quick Start Cal
0
1
EE CheckSum failed
2
CheckSum
0
1
The AMIS-53000 is in a state of operation that can accept instructions
1
Instruction Enable
0
1
ADC conversion complete
0
ADC Done
0
6.4.5.2.
Status/Flag2
The Status2 register provides information on the operating status of the part. The busy bit is asserted for any of the following reasons:
Calibration:
The busy bit will remain high for the duration of a calibration sequence. Status2 can be repeatedly polled during
a calibration sequence to determine when it’s complete.
Read/Write EE:
While the AMIS-53000 is reading from or writing to the EE, the busy bit will remain set.
Buffered RX:
When in receive mode, and a valid chip ID is found, the AMIS-53000 will begin processing of this packet.
During the time the packet is being processed, the busy bit will be set high.
Buffered TX:
After the command is given for transmit with the buffered packet option enabled, the busy bit will remain high
until the part has completed the actual transmission of the packet.
Housekeeping:
Busy is asserted during a housekeeping cycle.
Burst TX:
Busy is asserted during a Burst transmission.
46
AMI Semiconductor
– Aug. 05, Rev. 1.0
www.amis.com
相關PDF資料
PDF描述
AMIS-53000-M Frequency Agile Transceiver
AMIS-53050 Frequency Agile Transceiver
AMIS-710650 Color CIS Module Analog Video Output
AMIS-710650-A6 Color CIS Module Analog Video Output
AMIS-710651 Color CIS Module
相關代理商/技術參數
參數描述
AMIS53000/19608-001XT 制造商:AMI Semiconductor 功能描述: 制造商:NTE Electronics 功能描述:
AMIS53000/SAMPLE 制造商:AMI Semiconductor 功能描述: 制造商:NTE Electronics 功能描述:
AMIS-53000-I/A 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver
AMIS-53000-M 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver
AMIS-53050 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Tape and Reel 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*