- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C974 (Advanced Micro Devices, Inc.) PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems PDF資料下載
參數資料
| 型號： | AM79C974 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| 中文描述： | PCnetTM -的SCSI結合以太網和SCSI控制器PCI系統 |
| 文件頁數： | 87/153頁 |
| 文件大小： | 838K |
| 代理商： | AM79C974 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
P R E L I M I N A R Y
AMD
87
Am79C974
Clear FIFO Command
(Command Code 01h)
The Clear FIFO Command is used to initialize the SCSI
FIFO to the empty condition. The Current FIFO Register
(CFISREG) reflects the empty FIFO status and the bot-
tom of the FIFO is set to zero. No interrupt is generated
at the end of this command.
Reset Device Command
(Command Code 02h)
The Reset Device Command immediately stops any de-
vice operation and resets all the functions of the device.
Additionally, it returns the device to the disconnected
state and it generates a hard reset. The Reset Device
Command remains on the top of the Command Register
FIFO holding the device in the reset state until the No
Operation Command is loaded. Once loaded, the No
Operation command serves to re-enable the Command
Register.
Reset SCSI Bus Command
(Command Code 03h)
The Reset SCSI Bus Command forces the
SCSI^RST
signal active for a period of 25 ms, and drives the chip to
the Disconnected state. An interrupt is not generated
upon command completion, however, if bit 6 is set to ‘0’
in Control Register One (CNTLREG1), a SCSI Reset in-
terrupt will be issued.
SCSI Power Management Features
As a leader in low-voltage technology, AMD has incor-
porated power-saving features into the Am79C974.
Through hardware and software, the Am79C974 can be
powered down to reduce consumption during chip
inactivity.
SCSI Activity Pin
The SCSI Bus activity is reflected by the
BUSY
output
line. This signal, when active, indicates that the SCSI
Bus is in use, therefore the Am79C974 should not be
powered down. This signal is the logical equivalent to
the SCSI bus signal
BSY
, however, it is not physically
connected to the
BSY
signal on the bus. To correctly
identify the Bus Free State on the SCSI bus, this
BUSY
output line must be inactive for at least 250 ms (Selec-
tion Timeout period).
Reduced Power Mode
When there is no activity on the SCSI Bus, and there are
no pending commands, the Am79C974 may be pow-
ered down by turning off the input buffers on the SCSI
Bus lines (set bit 5 in Control Register Four (B)+34h).
For further power reduction, the internal registers may
be programmed to a predetermined state, and the input
clock disconnected via external logic.
Power Down Pin (PWDN Pin)
When PWDN is driven active, it sets the PWDN bit in the
Status Register (Bit 0, DMA Status Register (B)+54h),
signaling the Am79C974 that the host would like to
power down the SCSI interface. An interrupt is gener-
ated when this bit is first set.
Software Disk Spin-Down
Incorporated into the SCSI ROM BIOS and certain de-
vice driver’s of AMD’s software solution is a module
which physically spins down SCSI fixed disks when the
host system elects to enact power management on the
SCSI system. The software module is activated upon
the ROM BIOS and/or other device driver’s receipt of an
interrupt caused by the PWDN pin being driven active.
Upon receipt of this interrupt, the current software proc-
ess is suspended and software control is given to the
power management module.
When the power management module is activated, it
checks the status of all SCSI fixed disks on the system
under its control. The SCSI fixed disks that are idle are
issued a command to spin down their media. All fixed
disks that are active at the time will be scheduled for spin
down upon completion of their pending commands.
Once the BIOS and/or drivers have detected the com-
pletion of each fixed disk’s final pending commands,
they are issued the command to spin down as well.
To spin down the disk drives, the power management
module issues a SCSI command (1B– Start/Stop unit).
When the command is received by the drive, it spins
down and waits in an idle state. For multiple drives on
the SCSI bus, the power management driver spins
down each drive individually. The drives remain in the
idle state until the BIOS and/or driver receives a com-
mand for the particular fixed disk. Once this occurs, the
drive is issued the command to spin up. When the drive
has completely spun up and is ready, the pending com-
mand is issued to the drive. Only the particular fixed disk
issued the command is instructed to spin up. All other
drives will remain in the spun down state until a com-
mand is issued to them.
Note
: This sequence does not turn off the input buffers
as described in the previous section.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C974KCW | PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| AM79C975 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C974KC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C974KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| AM79C974KCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| AM79C975 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
發布緊急采購，3分鐘左右您將得到回復。