- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C970AKCW (ADVANCED MICRO DEVICES INC) PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product PDF資料下載
參數資料
| 型號： | AM79C970AKCW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 103/219頁 |
| 文件大?。?/td> | 1065K |
| 代理商： | AM79C970AKCW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁當前第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁
P R E L I M I N A R Y
AMD
103
Am79C970A
I/O Resources
The PCnet-PCI II controller requires 32 bytes of address
space for access to all the various internal registers as
well as to some setup information stored in an external
serial EEPROM. A software reset port is available, too.
The PCnet-PCI II controller supports mapping the ad-
dress space to both I/O and memory space. The value in
the PCI I/O Base Address register determines the start
address of the I/O address space. The register is typi-
cally programmed by the PCI configuration utility after
system power-up. The PCI configuration utility must
also set the IOEN bit in the PCI Command register to en-
able I/O accesses to the PCnet-PCI II controller. For
memory mapped I/O access, the PCI Memory Mapped
I/O Base Address register controls the start address of
the memory space. The MEMEN bit in the PCI Com-
mand register must also be set to enable the mode. Both
base address registers can be active at the same time.
The PCnet-PCI II controller supports two modes for ac-
cessing the I/O resources. For backwards compatibility
with AMD’s 16-bit Ethernet controllers, Word I/O is the
default mode after power up. The device can be config-
ured to DWord I/O mode by software.
I/O Registers
The PCnet-PCI II controller registers are divided into
two groups. The Control and Status Registers (CSR)
are used to configure the Ethernet MAC engine and to
obtain status information. The Bus Control Registers
(BCR) are use to configure the bus interface unit and the
LEDs. Both sets of registers are accessed using
indirect addressing.
The CSR and BCR share a common Register Address
Port (RAP). There are, however, separate data ports.
The Register Data Port (RDP) is used to access a CSR.
The BCR Data Port (BDP) is used to access a BCR.
In order to access a particular CSR location, the RAP
should first be written with the appropriate CSR ad-
dress. The RDP will then points to the selected CSR. A
read of the RDP will yield the selected CSR data. A write
to the RDP will write to the selected CSR. In order to ac-
cess a particular BCR location, the RAP should first be
written with the appropriate BCR address. The BDP will
then points to the selected BCR. A read of the BDP will
yield the selected BCR data. A write to the BDP will write
to the selected BCR.
Once the RAP has been written with a value, the RAP
value remains unchanged until another RAP write oc-
curs, or until an H_RESET or S_RESET occurs. RAP is
cleared to all ZEROs when an H_RESET or S_RESET
occurs. RAP is unaffected by setting the STOP bit.
Address PROM Space
The PCnet-PCI II controller allows for connection of a
serial EEPROM. The first 16 bytes of the EEPROM will
be automatically loaded into the Address PROM
(APROM) space after H_RESET. The Address PROM
space is a convenient place to store the value of the
48-bit IEEE station address. It can be overwritten by the
host computer. Its content has no effect on the operation
of the controller. The software must copy the station ad-
dress from the Address PROM space to the initialization
block or to CSR12-14 in order for the receiver to accept
unicast frames directed to this station.
The 6 bytes of IEEE station address occupy the first 6
locations of the Address PROM space. The next six
bytes are reserved. Bytes 12 and 13 should match the
value of the checksum of bytes 1 through 11 and 14 and
15. Bytes 14 and 15 should each be ASCII W (57h). The
above requirements must be met in order to be compat-
ible with AMD driver software.
The APROMWE bit (BCR2, bit 8) must be set to ONE to
enable write access to the Address PROM space.
Reset Register
A read of the Reset register creates an internal software
reset (S_RESET) pulse in the PCnet-PCI II controller.
The internal S_RESET pulse that is generated by this
access is different from both the assertion of the
hardware
RST
pin (H_RESET) and from the assertion of
the software STOP bit. Specifically, S_RESET is the
equivalent of the assertion of the
RST
pin (H_RESET)
except that S_RESET has no effect on the BCR or PCI
Configuration space locations or on the T-MAU.
The NE2100 LANCE based family of Ethernet cards
requires that a write access to the Reset register
follows each read access to the Reset register. The
PCnet-PCI II controller does not have a similar require-
ment. The write access is not required but it does not
have any effects.
Note that the PCnet-PCI II controller cannot service any
slave accesses for a very short time after a read access
of the Reset register, because the internal S_RESET
operation takes about 1
μ
s to finish. The PCnet-PCI II
controller will terminate all slave accesses with the as-
sertion of
DEVSEL
and
STOP
while
TRDY
is not as-
serted, signaling to the initiator to disconnect and retry
the access at a later time.
Word I/O Mode
After H_RESET, the PCnet-PCI II controller is pro-
grammed to operate in Word I/O mode. DWIO (BCR18,
bit 7) will be cleared to ZERO. The table below shows
how the 32 bytes of address space are used in Word
I/O mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C970AKC | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970A | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AVCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970 | PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus |
| AM79C971VCW | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C970AVC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AVC\\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AM79C970AVC\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: 制造商:AMD 功能描述: |
| AM79C970AVC-G | 制造商:Rochester Electronics LLC 功能描述: |
| AM79C970AVCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
發布緊急采購，3分鐘左右您將得到回復。