參數資料
型號： ADUC831BSZ-REEL
廠商： Analog Devices Inc
文件頁數： 22/76頁
文件大小： 0K
描述： IC MCU 62K FLASH ADC/DAC 52MQFP
標準包裝： 800
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 16MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 62KB（62K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量： 2.25K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 8x12b，D/A 2x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 52-QFP
包裝： 帶卷 (TR)
配用： EVAL-ADUC831QSZ-ND - KIT DEV FOR ADUC831 QUICK START
REV. 0
ADuC831
–29–
USING THE FLASH/EE DATA MEMORY
The 4 kBytes of Flash/EE data memory is configured as 1024
pages, each of four bytes. As with the other ADuC831 peripherals,
the interface to this memory space is via a group of registers mapped
in the SFR space. A group of four data registers (EDATA1–4)
are used to hold the four bytes of data at each page. The page is
addressed via the two registers EADRH and EADRL. Finally,
ECON is an 8-bit control register that may be written with one
of nine Flash/EE memory access commands to trigger various
read, write, erase, and verify functions.
A block diagram of the SFR interface to the Flash/EE data
memory array is shown in Figure 20.
ECON—Flash/EE Memory Control SFR
Programming of either the Flash/EE data memory or the Flash/EE
program memory is done through the Flash/EE memory control
SFR (ECON). This SFR allows the user to read, write, erase, or
verify the 4 kBytes of Flash/EE data memory or the 56 kBytes of
Flash/EE program memory.
BYTE 1
(0000H)
EDATA1
SFR
BYTE 1
(0004H)
BYTE 1
(0008H)
BYTE 1
(000CH)
BYTE 1
(0FF8H)
BYTE 1
(0FFCH)
BYTE 2
(0001H)
EDATA2
SFR
BYTE 2
(0005H)
BYTE 2
(0009H)
BYTE 2
(000DH)
BYTE 2
(0FF9H)
BYTE 2
(0FFDH)
BYTE 3
(0002H)
EDATA3
SFR
BYTE 3
(0006H)
BYTE 3
(000AH)
BYTE 3
(000EH)
BYTE 3
(0FFAH)
BYTE 3
(0FFEH)
BYTE 4
(0003H)
EDATA4
SFR
BYTE 4
(0007H)
BYTE 4
(000BH)
BYTE 4
(000FH)
BYTE 4
(0FFBH)
BYTE 4
(0FFFH)
01H
00H
02H
03H
3FEH
3FFH
PAGE
ADDRESS
(E
ADRH/L)
BYTE
ADDRESSES
ARE GIVEN IN
BRACKETS
Figure 20. Flash/EE Data Memory Control and Configuration
Table VII. ECON—Flash/EE Memory Commands
COMMAND DESCRIPTION
ECON VALUE
(NORMAL MODE) (Power-On Default)
(ULOAD MODE)
01H
Results in 4 bytes in the Flash/EE data memory,
Not Implemented. Use the MOVC instruction.
READ
addressed by the page address EADRH/L, being read
into EDATA1–4.
02H
Results in four bytes in EDATA1–4 being written to
Results in bytes 0-255 of internal XRAM being written
WRITE
the Flash/EE data memory, at the page address given by
to the 256 bytes of Flash/EE program memory at the
EADRH/L (0
≤ EADRH/L < 0400H.
page address given by EADRH. (0
≤ EADRH < E0H)
Note: The four bytes in the page being addressed must
Note: The 256 bytes in the page being addressed must
be pre-erased.
03H
Reserved Command
04H
Verifies if the data in EDATA1–4 is contained in the
Not Implemented. Use the MOVC and MOVX
VERIFY
page address given by EADRH/L. A subsequent read
instructions to verify the WRITE in software.
of the ECON SFR will result in a 0 being read if the
verification is valid, or a nonzero value being read to
indicate an invalid verification.
05H
Results in the Erase of the 4-byte page of Flash/EE data
Results in the 64-byte page of Flash/EE program
ERASE PAGE
memory addressed by the page address EADRH/L.
memory, addressed by the byte address EADRH/L
being erased. EADRL can equal any of 64 locations
within the page. A new page starts whenever EADRL
is equal to 00H, 40H, 80H, or C0H.
06H
Results in the erase of entire 4 kBytes of Flash/EE
Results in the Erase of the entire 56 kBytes of ULOAD
ERASE ALL
data memory.
Flash/EE program memory.
81H
Results in the byte in the Flash/EE data memory,
Not Implemented. Use the MOVC command.
READBYTE
addressed by the byte address EADRH/L, being read
into EDATA1. (0
≤ EADRH/L ≤ 0FFFH).
82H
Results in the byte in EDATA1 being written into
WRITEBYTE
Flash/EE data memory, at the byte address EADRH/L.
Flash/EE program memory, at the byte address
EADRH/L (0
≤ EADRH/L ≤ DFFFH).
0FH
Leaves the ECON instructions to operate on the
Enters NORMAL mode directing subsequent ECON
EXULOAD
Flash/EE data memory.
instructions to operate on the Flash/EE data memory.
F0H
Enters ULOAD mode, directing subsequent ECON
Leaves the ECON instructions to operate on the
ULOAD
instructions to operate on the Flash/EE program memory.
Flash/EE program memory.
相關PDF資料
PDF描述
ATSAM3X8CA-AU IC MCU 2X256KB CORTEX-M3 100-QFP
VE-B3M-IX-F4 CONVERTER MOD DC/DC 10V 75W
VE-B3M-IX-F3 CONVERTER MOD DC/DC 10V 75W
VE-B3M-IX-F1 CONVERTER MOD DC/DC 10V 75W
VE-B3M-IW-F4 CONVERTER MOD DC/DC 10V 100W
相關代理商/技術參數
參數描述
ADUC832 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC832BCP 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V/5V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 16.78MHZ 3.3/5V 56LFCSP - Bulk
ADUC832BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V/5V 56-Pin LFCSP EP T/R
ADUC832BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC832BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*