- 您現在的位置：買賣IC網 > PDF目錄24827 > 935268252557 (NXP SEMICONDUCTORS) 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | 935268252557 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-486-1, LQFP-144 |
| 文件頁數： | 80/80頁 |
| 文件大?。?/td> | 306K |
| 代理商： | 935268252557 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁
Philips Semiconductors
Preliminary specification
PDI1394L40
1394 enhanced AV link layer controller
2000 Dec 15
6
9.3
AV Interface 2
NOTE: This AV interface may be configured to transmit or receive according to the condition of “DIRAV1” bit in GLOBCSR register—default is
receive.
PIN No.
PIN SYMBOL
I/O
NAME AND FUNCTION
121
AV2ERR0/
LTLEND
I/O
CRC error, indicates bus packet containing AV2 D [7:0] had a CRC error, the current AV packet
is unreliable. This pin is also used to input the mode of LTLEND (Little Endian) bit after a chip
reset. An appropriate pull-up or pull-down resistor (22 k
recommended) should be connected
to place the pin in the desired state during reset. Please see details related to use of the
LTLEND bit in the “Host Interface” section (of the datasheet (Section 12.5).
122
AV2ERR1/
DATINV
I/O
Sequence Error. Indicates at least one source packet was lost before the current AV2 D [7:0]
data. This pin is also used to input the mode of DATINV (Data Invariant) bit after a chip reset.
An appropriate pull-up or pull-down resistor (22 k
recommended) should be connected to
place the pin in the desired state during reset. Please see details related to use of the DATINV
bit in the “Host Interface” section (of the datasheet (Section 12.5).
123
AV2ENDPCK
I
End of application packet indication from data source. Required only if input packet is not
multiple of 4 bytes. It can be tied LOW for data packets that are 4*N in size.
124
AV2CLK
I/O
External application clock. Rising edge active. This pin can be programmed to be an output
and the application clock. Depending on the configuration of AV Port 2 as transmitter or
receiver, the output enable is located in the ITXPKCTL register (address 0x020) or IRXPKCTL
register (address 0x040).
125
AV2FSYNC
I/O
Programmable frame sync, is set to input when AV interface 2 is a transmitter, and to output
when the interface is configures as a receiver. When the pin is an input, it is used to designate
a frame of data for Digital Video (DV). The signal is time stamped and transmitted in the SYT
field of ITXHQ2. When set to an output, the signal is derived from SYT field of IRXHQ2.
126
AV2 SY
I/O
SY Value: When port AV2 is configured as a transmitter, this pin is an input. When the AV port
is configured to as a receiver, the pin is an output. See the description for bit 0 of the
ITXCTL (0x034) and IRXCTL (0x054) registers.
127
AV2VALID
I/O
Indicates data on AV2 D [7:0] is valid.
128
AV2SYNC
I/O
Indicates that the data currently being clocked by the source under the condition of AV2VALID
is the start of an application packet. If the AV interface is configured as a receiver, then it will
assert AV2SYNC when an application packet becomes available and persist until the first data
of the packet is clocked out. Thus, AV2VALID may last for more than one cycle, but for exactly
one cycle in which AV2VALID is asserted.
142, 141, 140,
139, 136, 135,
134, 133
AV2 D[7:0]
I/O
Audio/Video Data 7 (MSB) through 0. Part of byte-wide interface to the AV layer 2.
I
When the AV port is configured as a receiver, this pin is an input. This is a flow control signal
that allows the application to indicate whether it is able to accept data flowing across
AV Interface 2. The AV interface responds to an inactive AV2READY by not asserting
AV2VALID, and thereby withholding data from the application.
The AV2READY signal is processed through one level of pipelining, which means that the
AV Link will accept data on the cycle in which AV2READY is de-asserted and will not accept
data on the cycle in which AV2READY is asserted.
143
AV2READY
O
When the AV port is configured to transmit, this pin is an output. This is a flow control signal
that allows the link chip to indicate whether it is able to accept data flowing across
AV Interface 2. The source of data, and external entity, responds to an inactive AV2READY by
not asserting AV2VALID, and thereby withholding data.
The AV2READY signal should be processed by the sink through one level of pipelining, which
means that the receiver must be able to accept data on the cycle in which AV2READY is
de-asserted. The receiving interface does not have to accept data on the cycle in which
AV2READY is asserted.
相關PDF資料 |
PDF描述 |
|---|---|
| 08008GOB | 125 A, 800 V, SCR, TO-209AC |
| 935268252551 | 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP144 |
| 08008GOC | 125 A, 800 V, SCR, TO-209AC |
| 08008GOD | 125 A, 800 V, SCR, TO-208AD |
| 08010GOB | 125 A, 1000 V, SCR, TO-209AC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
| 935269544557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3 |
| 935269987557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-1US1-V1.8 SUBBED TO 935269987557 |
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
發布緊急采購，3分鐘左右您將得到回復。