- 您現在的位置：買賣IC網 > PDF目錄364515 > 84301 84301 4-Port Fast Ethernet Controller manual 3/98 PDF資料下載
參數資料
| 型號： | 84301 |
| 英文描述： | 84301 4-Port Fast Ethernet Controller manual 3/98 |
| 中文描述： | 84301 4端口快速以太網控制器手冊3 / 98 |
| 文件頁數： | 26/62頁 |
| 文件大?。?/td> | 606K |
| 代理商： | 84301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
84301 4-Port
Fast Ethernet Controller
4-26
MD400158/D
and indicating whether the address is physical or logical.
Bit 7 of station address byte 5 is compared to the last bit of
the received destination address. The Station Address
should be programmed prior to enabling a port’s receiver.
3.6.3 Transmit Command Register
The transmit command register is an 8 bit register. Bits 0
through 3 of the Transmit Command Register function as
interrupt mask bits, which provide for control of the condi-
tions allowed to generate transmit interrupts. Each of the
four bits may be individually set or cleared. When set, the
occurrence of the associated condition will cause an
interrupt to be generated. The four specific conditions for
which interrupts may be generated are:
1. A Transmit FIFO underflow occurred while
transmitting the packet.
2. A collision occurred while transmitting the packet.
3. A transmit error condition occurred i.e,
(Carrier sense never went active during
transmission or went rom an active o nactive state
during transmission or 16 collisions occurred for a
transmit packet or a late collision occurred).
4.
The packet was transmitted successfully.
Interrupts are cleared by following the procedure given in
the section entitled "Clearing Interrupts" in section 3.3.5.
7
6
5
4
3
2
1
0
Bit
Value
Definition
R/W*
Default Values
After Reset
0
‘1’
Generates an interrupt on the
occurrence of a transmit underflow.
R/W
0
1
‘1’
Generates an interrupt on the
occurrence of a collision during
the transmission of a packet.
R/W
0
2
‘1’
Generates an interrupt on the
occurrence of a transmit error
condition.
R/W
0
3
‘1’
Generates an interrupt on the
occurrence of a successful
transmission.
R/W
0
4
‘1’
Sets the chip into the MII mode
R/W
0
5
‘1’
Register
Code Bit
0.
These two bits are
used in conjunction
with the A[4:0]
address pins to access
registers other than the
Receive and Transmit
command registers
within a port.
R/W
0
6
‘1’
Register
Code Bit
1.
R/W
0
7
‘0’
Test Mode.
Note: This bit should not be
written HIGH under normal
circumstances.
R/W
0
Transmit Command Register Format
* This register can be used as a write only register or a Read/Write register by configuring the address
inputs accordingly. Please refer to “3.6.1 Internal Port Register Addressing Table” for details.
相關PDF資料 |
PDF描述 |
|---|---|
| 84301 | 4-Port Fast Ethernet Controller( 4端口快速以太網控制器) |
| 84717000 | MINIATURNAEHERUNGSSCHALTER 4MM GLATT PNP |
| 84717002 | MINIATURNAEHERUNGSSCHALTER M5 PNP |
| 84717100 | MINIATURNAEHERUNGSSCHALTER 4MM GLATT NPN |
| 84717102 | MINIATURNAEHERUNGSSCHALTER M5 NPN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8430100000 | 功能描述:OPTOCOUPLER 115VAC/DC 1 CH PLUG RoHS:是 類別:隔離器 >> 光隔離器 - 晶體管，光電輸出 系列:- 標準包裝:1,500 系列:NEPOC 通道數:1 輸入類型:DC 電壓 - 隔離:2500Vrms 電流傳輸比（最小值）:20% @ 16mA 電流傳輸比（最大）:- 輸出電壓:7V 電流 - 輸出 / 通道:8mA 電流 - DC 正向(If):25mA Vce飽和（最大）:- 輸出類型:有 Vcc 的晶體管 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| 8430-1032-A-0 | 制造商:RAF Electronic Hardware 功能描述: |
| 8430110000 | 功能描述:OPTOCOUPLER 24VAC/DC 4CH PLUG RoHS:是 類別:隔離器 >> 光隔離器 - 晶體管，光電輸出 系列:- 標準包裝:1,500 系列:NEPOC 通道數:1 輸入類型:DC 電壓 - 隔離:2500Vrms 電流傳輸比（最小值）:20% @ 16mA 電流傳輸比（最大）:- 輸出電壓:7V 電流 - 輸出 / 通道:8mA 電流 - DC 正向(If):25mA Vce飽和（最大）:- 輸出類型:有 Vcc 的晶體管 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| 8430114 | 制造商:SAB NORTH AMERICA 功能描述:SL843C continuous flex servo motor feedback cable 26/10c + 20/4c UL CSA shielded |
| 843011AG | 制造商:Integrated Device Technology Inc 功能描述:843011AG - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。