- 您現在的位置：買賣IC網 > PDF目錄371369 > 21440 (Intel Corp.) Multiport 10/100Mb/s Ethernet Controller(多端口10/100Mb/s 以太網控制器) PDF資料下載
參數資料
| 型號： | 21440 |
| 廠商： | Intel Corp. |
| 英文描述： | Multiport 10/100Mb/s Ethernet Controller(多端口10/100Mb/s 以太網控制器) |
| 中文描述： | 多端口10/100Mb/s以太網控制器（多端口支持10/100Mbps以太網控制器） |
| 文件頁數： | 13/92頁 |
| 文件大?。?/td> | 1352K |
| 代理商： | 21440 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
21440 Multiport 10/100Mb/s Ethernet Controller
2-1
Pinout
2
This chapter describes the 21440 pinout.
2.1
Signal Description
Table 2-1
describes the signals that the 21440 uses.
The following conventions are used in the signal names:
The following abbreviations are used in
Table 2-1
:
_l
Indicates that the pin is active low.
{i}
The i subscript appended to pin names indicates that
each port has its own pin (numbered from 0 to 7).
I
=
Input
O
=
Output
OD
=
Open Drain
I/O
=
Input/Output
Table 2-1. Signal Descriptions (Sheet 1 of 3)
Signal Name
CPU Interface
I/O
Pin Description
cs_l
I
Chip select.
This pin must be asserted to enable CPU access to the chip registers.
CPU port select.
Selects one of the 8 internal ports for register accesses.
Read strobe.
Upon assertion, the address signals cadd[9:0], cs_l, and cps[2:0] are latched by the chip.
Deassertion occurs after the read data is latched from the cdat[7:0] bus.
Write strobe.
Upon assertion, the address signals cadd[9:0], cs_l, and cps[2:0] are latched by the chip.
Deassertion must occur while the data is valid on the cdat[7:0] bus.
Ready indication.
When asserted, indicates that either data is stable on the cdat[7:0] bus during read
access or that data was latched by the chip during write access.
Address bus.
Selects one of the internal registers to be accessed.
CPU data bus.
Carries data to be written to or read from the registers.
Interrupt lines.
These signals are asserted following a variety of programmable conditions. Deassertion
occurs after reading the events that cause the interrupt, unless another interrupt is
registered meanwhile.
General reset.
Upon reset, all the registers are reset to their default values and the FIFOs are flushed.
cps[2:0]
I
crd_l
I
cwr_l
I
crdy_l
OD
cadd[9:0]
I
cdat[7:0]
I/O
cint{i}_l
OD
reset_l
I
相關PDF資料 |
PDF描述 |
|---|---|
| 21446 | Net186-EVAL-KT? 24.9KB (PDF) |
| 2145 | MONITORKABEL SUN BUCHSE SVGA STECKER |
| 2148C | MONITORKABEL SUN STECKER SVGA BUCHSE |
| 2148D | MONITORKABEL SUN STECKER SVGA STECKER |
| 2148 | MONITORKABEL SUN VGA ADAPTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2-1440000-2 | 制造商:TE Connectivity 功能描述:relay, OMR-C-105H,V000 |
| 2-1440000-3 | 功能描述:低信號繼電器 - PCB OMR-C-105H V300 RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| 2-1440000-5 | 功能描述:低信號繼電器 - PCB OMR-C-109H V530 RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| 2-1440000-6 | 制造商:TE Connectivity 功能描述:Electromechanical Relay SPST-NO 0.5A 12VDC 1.05KOhm Through Hole 制造商:TE Connectivity 功能描述:EM RLY SPST-NO 0.5A 12VDC 1.05KOHM TH - Bulk 制造商:TE Connectivity 功能描述:RELAY REED SPST 500MA 12V |
| 2-1440001-1 | 功能描述:通用繼電器 OMI-SH-206L 594 RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
發布緊急采購，3分鐘左右您將得到回復。