TABLE
參數資料
型號： XRT86VL38IB-F
廠商： Exar Corporation
文件頁數： 98/160頁
文件大?。?/td> 0K
描述： IC LIU/FRAMER T1/E1/J1 8CH 420BG
標準包裝： 40
控制器類型： T1/E1/J1 調幀器，LIU
電源電壓： 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 420-BBGA
供應商設備封裝： 420-PBGA
包裝： 托盤
其它名稱： 1016-1487
XRT86VL38IB-F-ND
XRT86VL38
37
OCTAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
REV. V1.2.0
TABLE 21: SLIP BUFFER CONTROL REGISTER (SBCR)
HEX ADDRESS: 0Xn116
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
7
TxSB_ISFIFO
R/W
0
Transmit Slip Buffer Mode
This bit permits the user to configure the Transmit Slip Buffer to function as
either “Slip-Buffer” Mode, or as a “FIFO”, as depicted below.
0 - Configures the Transmit Slip Buffer to function as a “Slip-Buffer”.
1 - Configures the Transmit Slip Buffer to function as a “FIFO”.
NOTE: Transmit slip buffer is only used in high-speed or multiplexed mode
where TxSERCLKn must be configured as inputs only. Users must
make sure that the “Transmit Direction” timing (i.e. TxMSYNC) and
the TxSerClk input clock signal are synchronous to prevent any
transmit slips from occuring.
NOTE: The data latency is dictated by FIFO Latency in the FIFO Latency
Register (register 0xn117).
6-5
Reserved
-
Reserved
4
SB_FORCESF
R/W
0
Force Signaling Freeze
This bit permits the user to freeze any signaling update on the RxSIGn output
pin as well as the Receive Signaling Array Register -RSAR (0xn500-0xn51F)
until this bit is cleared.
0 = Signaling on RxSIG and RSAR is updated immediately.
1 = Signaling on RxSIG and RSAR is not updated until this bit is set to ‘0’.
3
SB_SFENB
R/W
0
Signal Freeze Enable Upon Buffer Slips
This bit enables signaling freeze for one multiframe after the receive buffer
slips.
If signaling freeze is enabled, then the “Receive Channel” will freeze all sig-
naling updates on RxSIG pin and RSAR (0xn500-0xn51F) for at least “one-
multiframe” period, after a “slip-event” has been detected within the “Receive
Slip Buffer”.
0 = Disables signaling freeze for one multi-frame after receive buffer slips.
1 = Enables signaling freeze for one multi-frame after receive buffer slips.
2
SB_SDIR
R/W
1
Slip Buffer (RxSync) Direction Select
This bit permits user to select the direction of the receive frame boundary
(RxSYNC) signal if the receive buffer is enabled. (i.e. SB_ENB[1:0] = 01 or
10). If slip buffer is bypassed, RxSYNC is always an output pin.
0 = Selects the RxSync signal as an output
1 = Selects the RxSync signal as an input
相關PDF資料
PDF描述
V72A36C400BF CONVERTER MOD DC/DC 36V 400W
V72A36C400BL3 CONVERTER MOD DC/DC 36V 400W
V72A36C400BL CONVERTER MOD DC/DC 36V 400W
V72A28C400BG3 CONVERTER MOD DC/DC 28V 400W
V72A28C400BG CONVERTER MOD DC/DC 28V 400W
相關代理商/技術參數
參數描述
XRT86VL38IB-F 制造商:Exar Corporation 功能描述:T1/E1 Framer Combo IC
XRT86VL3X 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VL3X_07 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VL3X_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VX38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*